1READ(2)                    Linux Programmer's Manual                   READ(2)
2
3
4

NAME

6       read - read from a file descriptor
7

SYNOPSIS

9       #include <unistd.h>
10
11       ssize_t read(int fd, void *buf, size_t count);
12

DESCRIPTION

14       read()  attempts to read up to count bytes from file descriptor fd into
15       the buffer starting at buf.
16
17       On files that support seeking, the read operation commences at the file
18       offset, and the file offset is incremented by the number of bytes read.
19       If the file offset is at or past the end of file, no  bytes  are  read,
20       and read() returns zero.
21
22       If count is zero, read() may detect the errors described below.  In the
23       absence of any errors, or if read() does not check for errors, a read()
24       with a count of 0 returns zero and has no other effects.
25
26       According to POSIX.1, if count is greater than SSIZE_MAX, the result is
27       implementation-defined; see NOTES for the upper limit on Linux.
28

RETURN VALUE

30       On success, the number of bytes read is returned (zero indicates end of
31       file),  and the file position is advanced by this number.  It is not an
32       error if this number is smaller than the  number  of  bytes  requested;
33       this  may happen for example because fewer bytes are actually available
34       right now (maybe because we were close to end-of-file,  or  because  we
35       are  reading  from  a  pipe, or from a terminal), or because read() was
36       interrupted by a signal.  See also NOTES.
37
38       On error, -1 is returned, and errno  is  set  appropriately.   In  this
39       case,  it  is  left  unspecified  whether  the  file  position (if any)
40       changes.
41

ERRORS

43       EAGAIN The file descriptor fd refers to a file other than a socket  and
44              has  been  marked  nonblocking  (O_NONBLOCK), and the read would
45              block.  See open(2) for further details on the O_NONBLOCK flag.
46
47       EAGAIN or EWOULDBLOCK
48              The file descriptor fd refers to a socket and  has  been  marked
49              nonblocking    (O_NONBLOCK),   and   the   read   would   block.
50              POSIX.1-2001 allows either error to be returned for  this  case,
51              and  does not require these constants to have the same value, so
52              a portable application should check for both possibilities.
53
54       EBADF  fd is not a valid file descriptor or is not open for reading.
55
56       EFAULT buf is outside your accessible address space.
57
58       EINTR  The call was interrupted by a signal before any data  was  read;
59              see signal(7).
60
61       EINVAL fd  is attached to an object which is unsuitable for reading; or
62              the file was opened with  the  O_DIRECT  flag,  and  either  the
63              address  specified  in buf, the value specified in count, or the
64              file offset is not suitably aligned.
65
66       EINVAL fd was created via a call to  timerfd_create(2)  and  the  wrong
67              size  buffer was given to read(); see timerfd_create(2) for fur‐
68              ther information.
69
70       EIO    I/O error.  This will happen for example when the process is  in
71              a  background  process group, tries to read from its controlling
72              terminal, and either it is ignoring or blocking SIGTTIN  or  its
73              process  group  is  orphaned.  It may also occur when there is a
74              low-level I/O error while reading from a disk or tape.   A  fur‐
75              ther  possible  cause of EIO on networked filesystems is when an
76              advisory lock had been taken out on the file descriptor and this
77              lock  has been lost.  See the Lost locks section of fcntl(2) for
78              further details.
79
80       EISDIR fd refers to a directory.
81
82       Other errors may occur, depending on the object connected to fd.
83

CONFORMING TO

85       SVr4, 4.3BSD, POSIX.1-2001.
86

NOTES

88       The types size_t and ssize_t are,  respectively,  unsigned  and  signed
89       integer data types specified by POSIX.1.
90
91       On  Linux,  read()  (and  similar  system  calls) will transfer at most
92       0x7ffff000 (2,147,479,552) bytes, returning the number of  bytes  actu‐
93       ally transferred.  (This is true on both 32-bit and 64-bit systems.)
94
95       On NFS filesystems, reading small amounts of data will update the time‐
96       stamp only the first time, subsequent calls may not  do  so.   This  is
97       caused  by  client  side attribute caching, because most if not all NFS
98       clients leave st_atime (last file access time) updates to  the  server,
99       and  client side reads satisfied from the client's cache will not cause
100       st_atime updates on the server as there are no server-side reads.  UNIX
101       semantics  can  be obtained by disabling client-side attribute caching,
102       but in most situations this will substantially increase server load and
103       decrease performance.
104

BUGS

106       According to POSIX.1-2008/SUSv4 Section XSI 2.9.7 ("Thread Interactions
107       with Regular File Operations"):
108
109           All of the following functions shall be atomic with respect to each
110           other in the effects specified in POSIX.1-2008 when they operate on
111           regular files or symbolic links: ...
112
113       Among the APIs subsequently listed are read() and readv(2).  And  among
114       the  effects  that  should be atomic across threads (and processes) are
115       updates of the file offset.  However, on  Linux  before  version  3.14,
116       this  was  not  the  case:  if  two  processes  that share an open file
117       description (see open(2)) perform a read() (or readv(2))  at  the  same
118       time, then the I/O operations were not atomic with respect updating the
119       file offset, with the result that the reads in the two processes  might
120       (incorrectly)  overlap  in the blocks of data that they obtained.  This
121       problem was fixed in Linux 3.14.
122

SEE ALSO

124       close(2), fcntl(2), ioctl(2), lseek(2), open(2), pread(2),  readdir(2),
125       readlink(2), readv(2), select(2), write(2), fread(3)
126

COLOPHON

128       This  page  is  part of release 4.15 of the Linux man-pages project.  A
129       description of the project, information about reporting bugs,  and  the
130       latest     version     of     this    page,    can    be    found    at
131       https://www.kernel.org/doc/man-pages/.
132
133
134
135Linux                             2018-02-02                           READ(2)
Impressum