1IPICMG(8)                   System Manager's Manual                  IPICMG(8)
2
3
4

NAME

6       ipmiutil picmg - send specific PICMG extended IPMI commands
7
8

SYNOPSIS

10       ipmiutil picmg [-mixNUPREFJTVY] <parameters>
11
12

DESCRIPTION

14       This  ipmiutil picmg subcommand sends specific PICMG/ATCA extended IPMI
15       commands to the firmware.
16
17       This utility can use either the /dev/ipmi0 driver  from  OpenIPMI,  the
18       /dev/imb  driver  from  Intel,  the  /dev/ipmikcs  driver from valinux,
19       direct user-space IOs, or the IPMI LAN interface if -N.
20
21

OPTIONS

23       Command line options are described below.
24
25       -i 00  This option specifies a specific FRU  ID  to  show.   The  input
26              value  should be in hex (0b, 1a, etc.), as shown from the sensor
27              SDR output.  The default FRU ID is zero (0).
28
29       -m 002000
30              Show FRU for a specific MC (e.g. bus 00, sa 20, lun  00).   This
31              could  be  used  for  PICMG or ATCA blade systems.  The trailing
32              character, if present, indicates SMI addressing if 's', or  IPMB
33              addressing if 'i' or not present.
34
35       -x     Causes extra debug messages to be displayed.
36
37       -N nodename
38              Nodename  or IP address of the remote target system.  If a node‐
39              name is specified, IPMI LAN interface is  used.   Otherwise  the
40              local system management interface is used.
41
42       -U rmt_user
43              Remote  username  for the nodename given.  The default is a null
44              username.
45
46       -P/-R rmt_pswd
47              Remote password for the nodename given.  The default is  a  null
48              password.
49
50       -E     Use the remote password from Environment variable IPMI_PASSWORD.
51
52       -F drv_t
53              Force  the  driver  type  to one of the followng: imb, va, open,
54              gnu, landesk, lan, lan2, lan2i, kcs, smb.  Note that lan2i means
55              lan2  with  intelplus.   The  default is to detect any available
56              driver type and use it.
57
58       -J     Use  the  specified  LanPlus   cipher   suite   (0   thru   14):
59              0=none/none/none,       1=sha1/none/none,      2=sha1/sha1/none,
60              3=sha1/sha1/cbc128,  4=sha1/sha1/xrc4_128,  5=sha1/sha1/xrc4_40,
61              6=md5/none/none, ... 14=md5/md5/xrc4_40.  Default is 3.
62
63       -T     Use  a  specified  IPMI  LAN Authentication Type: 0=None, 1=MD2,
64              2=MD5, 4=Straight Password, 5=OEM.
65
66       -V     Use a specified IPMI  LAN  privilege  level.  1=Callback  level,
67              2=User level, 3=Operator level, 4=Administrator level (default),
68              5=OEM level.
69
70       -Y     Yes, do prompt the  user  for  the  IPMI  LAN  remote  password.
71              Alternatives for the password are -E or -P.
72
73

PARAMETERS

75       picmg <parameters>
76
77
78              properties
79                     Get  PICMG  properties  may  be  used to obtain and print
80                     Extension major version  information,  PICMG  identifier,
81                     FRU Device ID and Max FRU Device ID.
82
83
84              addrinfo
85
86                     Get  address information.  This command may return infor‐
87                     mation on the Hardware address, IPMB-0 Address,  FRU  ID,
88                     Site/Entity ID, and Site/Entity Type.
89
90              frucontrol <fru id> <options>
91
92                     Set various control options:
93
94                     0x00      - Cold Reset
95
96                     0x01      - Warm Reset
97
98                     0x02      - Graceful Reboot
99
100                     0x03      - Issue Diagnostic Interrupt
101
102                     0x04      - Quiesce [AMC only]
103
104                     0x05-0xFF - Cold Reset
105
106              activate <fru id>
107
108                     Activate the specified FRU.
109
110              deactivate <fru id>
111
112                     Deactivate the specified FRU.
113
114              policy get <fru id>
115
116                     Get FRU activation policy.
117
118              policy set <fru id> <lockmask> <lock>
119
120                     Set  FRU  activation policy.  lockmask is 1 or 0 to indi‐
121                     cate action on the deactivation or activation locked  bit
122                     respectively.  lock is 1 or 0 to set/clear locked bit.
123
124              portstate set|getall|getgranted|getdenied <parameters>
125
126                     Get  or set various port states.  See usage for parameter
127                     details.
128
129
130
131

EXAMPLES

133       ipmiutil picmg properties
134       Gets PICMG properties from the default target  address  (slave  address
135       0x20).
136
137       ipmiutil picmg -N 192.168.1.1 -U root -P pswd addrinfo
138       Gets PICMG Address Information from the specified IP address.
139
140

SEE ALSO

142       ipmiutil(8)   ialarms(8)  iconfig(8)  idiscover(8)  ievents(8)  ifru(8)
143       igetevent(8) ihealth(8) ilan(8) ireset(8) isel(8) isensor(8) iserial(8)
144       isol(8) iwdt(8)
145
146

WARNINGS

148       See http://ipmiutil.sourceforge.net/ for the latest version of ipmiutil
149       and any bug fix list.
150
151

153       Copyright (C) 2010  Kontron America, Inc.
154
155       See the file COPYING in the distribution  for  more  details  regarding
156       redistribution.
157
158       This  utility  is  distributed  in the hope that it will be useful, but
159       WITHOUT ANY WARRANTY.
160
161

AUTHOR

163       Andy Cress <arcress at users.sourceforge.net>
164
165
166
167
168                           Version 1.0: 04 Jun 2010                  IPICMG(8)
Impressum