1MM2GV(1)                    General Commands Manual                   MM2GV(1)
2
3
4
5delim $$
6

NAME

8       mm2gv - Matrix Market-DOT converters
9

SYNOPSIS

11       mm2gv [ -cluv?  ] [ -Ui ] [ -ooutfile ] [ file ]
12

DESCRIPTION

14       mm2gv  converts  a sparse matrix of the Matrix Market format to a graph
15       in the GV (formerly DOT) format.  If the matrix M is  not  square,  the
16       graph  is  considered bipartite and the matrix is viewed as a bipartite
17       graph adjacency matrix, with the rows and columns of the matrix  speci‐
18       fying  the  two sets of vertices. Equivalently, the matrix is converted
19       into a symmetric square matrix
20
21           0       M
22       $M sup T$   0
23       a block matrix with square blocks of 0's in the upper  left  and  lower
24       right, the upper right block being M and the lower left block being the
25       transpose of M.  This matrix is then viewed as the adjacency matrix  of
26       the graph.
27
28       For  a  square matrix, mm2gv uses it directly as an adjacency matrix if
29       its pattern of non-zero entries is symmetric; otherwise, it will  treat
30       it  as  a bipartite graph as with the case of non-square matrices. This
31       behavior can be modified by the -U flag.
32

OPTIONS

34       The following options are supported:
35
36       -c     This flag causes mm2gv to assign colors to the edges. The matrix
37              element  is scaled to the range [0,1] depending on where it lies
38              between the minimum and maximum set matrix values.  This  scaled
39              value  is  used as the "wt" attribute of the corresponding edge.
40              In addition, this scalar value is mapped to an RGB value,  which
41              is stored as the edge "color".
42
43       -l     If  set, mm2gv attaches a label to the graph indicating the base
44              name of the input file, and the number of nodes and edges.
45
46       -u     If specified, the graph is assumed to be undirected. By default,
47              the graph generated is directed.
48
49       -v     This  flag  causes mm2gv to store the matrix values as the "len"
50              attribute of the corresponding edge.
51
52       -Ubflag
53              Specifies how square matrices are handled.  If  bflag  is  0,  a
54              square matrix will always be treated as an adjacency matrix.  If
55              bflag is 1 (the default), a square matrix with a symmetric  pat‐
56              tern  of  non-zero  entries will be used as an adjacency matrix;
57              otherwise, it will be used a bipartite graph.  If bflag is 2,  a
58              symmetric matrix will be used as an adjacency matrix; otherwise,
59              it will be used a bipartite graph.  If bflag  is  3,  any  input
60              matrix will be treated like a bipartite graph.
61
62       -ooutfile
63              Prints output to the file outfile. If not given, mm2gv uses std‐
64              out.
65
66
67       OPERANDS
68              The following operand is supported:
69
70       file    Name of the file in MatrixMarket format.  If no file operand is
71               specified, the standard input will be used.
72

RETURN CODES

74       Return  0  if there were no problems during conversion; and non-zero if
75       any error occurred.
76

AUTHORS

78       Yifan Hu <yifanhu@yahoo.com>
79       Emden R. Gansner <erg@graphviz.com>
80

ADDITIONAL INFO

82       See http://math.nist.gov/MatrixMarket/ for description  of  the  format
83       and  http://www.cise.ufl.edu/research/sparse/matrices/ for a large col‐
84       lection of sparse matrices in this format.
85
86
87
88                                 31 July 2008                         MM2GV(1)
Impressum