1NVMETCLI(8) NVMETCLI(8)
2
6 nvmetcli - Configure NVMe-over-Fabrics Target.
7
9 nvmetcli
10 nvmetcli clear
11 nvmetcli restore [filename.json]
12
14 nvmetcli is a program used for viewing, editing, saving, and starting a
15 Linux kernel NVMe Target, used for an NVMe-over-Fabrics network
16 configuration. It allows an administrator to export a storage resource
17 (such as NVMe devices, files, and volumes) to a local block device and
18 expose them to remote systems based on the NVMe-over-Fabrics
19 specification from http://www.nvmexpress.org.
20 nvmetcli is run as root and has two modes:
22 1. An interactive configuration shell
24 2. Command-line mode which uses an argument
26
28 The term NQN used throughout this man page is the NVMe Qualified Name
29 format which an NVMe endpoint (device, subsystem, etc) must follow to
30 guarantee a unique name under the NVMe standard. Any name in a network
31 system setup can be used, but if it does not follow the NQN format, it
32 may not be unique on an NVMe-over-Fabrics network.
33 Note that some of the fields set for an NVMe Target port under
35 interactive mode are defined in the "Discovery Log Page" section of
36 NVMe-over-Fabrics specification. Each NVMe Target has a discovery
37 controller mechanism that an NVMe Host can use to determine the NVM
38 subsystems it can access. nvmetcli can be used to add a new record to
39 the discovery controller upon each new subsystem entry and port entry
40 that the newly created subsystem entry binds to (see OPTIONS and
41 EXAMPLES sections). Each NVMe Host only gets to see the discovery
42 entries defined in /subsystems/[NQN NAME]/allowed_hosts and the IP port
43 it is connected to the NVMe Target. An NVMe Host can retrieve these
44 discovery logs via the nvme-cli tool
45 (https://github.com/linux-nvme/nvme-cli).
46
48 Interactive Configuration Shell
49 To start the interactive configuration shell, type nvmetcli on the
51 command-line. nvmetcli interacts with the Linux kernel NVMe Target
52 configfs subsystem starting at base nvmetcli directories /port,
53 /subsystem, and /host. Configuration changes entered by the
54 administrator are made immediately to the kernel target configuration.
55 The following commands can be used while in the interactive
56 configuration shell mode:
57 ┌───────────────────────────┬────────────────────────────┐
59 │ │ │
60 │cd │ Allows to move around the │
61 │ │ tree. │
62 ├───────────────────────────┼────────────────────────────┤
63 │ │ │
64 │ls │ Lists contents of current │
65 │ │ tree node. │
66 ├───────────────────────────┼────────────────────────────┤
67 │ │ │
68 │create [NQN name]/[#] │ Create a new object using │
69 │ │ the specified name or │
70 │ │ number. If a [NQN │
71 │ │ name]/[#] is not │
72 │ │ specified, a random entry │
73 │ │ will be used. │
74 ├───────────────────────────┼────────────────────────────┤
75 │ │ │
76 │delete [NQN name]/[#] │ Delete an object with the │
77 │ │ specified name or number. │
78 ├───────────────────────────┼────────────────────────────┤
79 │ │ │
80 │set attr │ Used under │
81 │allow_any_host=[0/1] │ /subsystems/[NQN name] to │
82 │ │ specify if any NVMe Host │
83 │ │ can connect to the │
84 │ │ subsystem. │
85 ├───────────────────────────┼────────────────────────────┤
86 │ │ │
87 │set device path=[device │ Used under │
88 │path] │ /subsystems/[NQN │
89 │ │ name]/namespaces to set │
90 │ │ the (storage) device to be │
91 │ │ used. │
92 ├───────────────────────────┼────────────────────────────┤
93 │ │ │
94 │set device nguid=[string] │ Used under │
95 │ │ /subsystems/[NQN │
96 │ │ name]/namespaces to set │
97 │ │ the unique id of the │
98 │ │ device to the defined │
99 │ │ namespace. │
100 ├───────────────────────────┼────────────────────────────┤
101 │ │ │
102 │enable/disable │ Used under │
103 │ │ /subsystems/[NQN │
104 │ │ name]/namespaces to enable │
105 │ │ and disable the namespace. │
106 ├───────────────────────────┼────────────────────────────┤
107 │ │ │
108 │set addr [discovery log │ Used under /ports/[#] to │
109 │page field]=[string] │ create a port which access │
110 │ │ is allowed. See EXAMPLES │
111 │ │ for more information. │
112 ├───────────────────────────┼────────────────────────────┤
113 │ │ │
114 │saveconfig [filename.json] │ Save the NVMe Target │
115 │ │ configuration in .json │
116 │ │ format. Without specifying │
117 │ │ the filename this will │
118 │ │ save as │
119 │ │ /etc/nvmet/config.json. │
120 │ │ This file is in JSON │
121 │ │ format and can be edited │
122 │ │ directly using a prefered │
123 │ │ file editor. │
124 ├───────────────────────────┼────────────────────────────┤
125 │ │ │
126 │exit │ Quits interactive │
127 │ │ configuration shell mode. │
128 └───────────────────────────┴────────────────────────────┘
129 Command Line Mode
131 Typing nvmetcli [cmd] on the command-line will execute a command and
133 not enter the interactive configuration shell.
134 ┌────────────────────────┬───────────────────────────┐
136 │ │ │
137 │restore [filename.json] │ Loads a saved NVMe Target │
138 │ │ configuration. Without │
139 │ │ specifying the filename │
140 │ │ this will use │
141 │ │ /etc/nvmet/config.json. │
142 ├────────────────────────┼───────────────────────────┤
143 │ │ │
144 │clear │ Clears a current NVMe │
145 │ │ Target configuration. │
146 ├────────────────────────┼───────────────────────────┤
147 │ │ │
148 │ls │ Dumps the current NVMe │
149 │ │ Target configuration. │
150 └────────────────────────┴───────────────────────────┘
151
153 Make sure to run nvmetcli as root, the nvmet module is loaded, your
154 devices and all dependent modules are loaded, and configfs is mounted
155 on /sys/kernel/config using:
156 mount -t configs none /sys/kernel/config
158 The following section walks through a configuration example.
160 · To get started with the interactive mode and the nvmetcli command
162 prompt, type (in root):
163 # ./nvmetcli
165 ...>
166 · Create a subsystem. If you do not specify a name a NQN will be
168 generated, which is probably the best choice. We don’t do it here
169 as the name would be random:
170 > cd /subsystems
172 ...> create testnqn
173 · Add access for a specific NVMe Host by it’s NQN:
175 ...> cd /hosts
177 ...> create hostnqn
178 ...> cd /subsystems/testnqn
179 ...> set attr allow_any_host=0
180 ...> cd /subsystems/testnqn/allowed_hosts/
181 ...> create hostnqn
182 · Remove access of a subsystem by deleting the Host NQN:
184 ...> cd /subsystems/testnqn/allowed_hosts/
186 ...> delete hostnqn
187 · Alternatively this allows any Host to connect to the subsystsem.
189 Only use this in tightly controlled environments:
190 ...> cd /subsystems/testnqn/
192 ...> set attr allow_any_host=1
193 · Create a new namespace. If you do not specify a namespace ID the
195 fist unused one will be used:
196 ...> cd /subsystems/testnqn/namespaces
198 ...> create 1
199 ...> cd 1
200 ...> set device path=/dev/nvme0n1
201 ...> enable
202 Note that in the above setup the device_nguid attribute does not have
204 to be set for correct NVMe Target functionality (but to correctly match
205 a namespace to the exact device upon clear and restore operations, it
206 is advised to set the device_nguid parameter).
207 · Create a loopback port that can be used with nvme-loop module on
209 the same physical machine...
210 ...> cd /ports/
212 ...> create 1
213 ...> cd 1/
214 ...> set addr trtype=loop
215 ...> cd subsystems/
216 ...> create testnqn
217 · or create an RDMA (IB, RoCE, iWarp) port using IPv4 addressing.
219 4420 is the IANA assigned default port for NVMe over Fabrics using
220 RDMA:
221 ...> cd /ports/
223 ...> create 2
224 ...> cd 2/
225 ...> set addr trtype=rdma
226 ...> set addr adrfam=ipv4
227 ...> set addr traddr=192.168.6.68
228 ...> set addr trsvcid=4420
229 ...> cd subsystems/
230 ...> create testnqn
231 · or create an FC port. traddr is the WWNN/WWPN of the FC port.
233 ...> cd /ports/
235 ...> create 3
236 ...> cd 3/
237 ...> set addr trtype=fc
238 ...> set addr adrfam=fc
239 ...> set addr traddr=nn-0x1000000044001123:pn-0x2000000055001123
240 ...> set addr trsvcid=none
241 ...> cd subsystems/
242 ...> create testnqn
243 · Saving the NVMe Target configuration:
245 ./nvmetcli
247 ...> saveconfig test.json
248 · Loading an NVMe Target configuration:
250 ./nvmetcli restore test.json
252 · Clearing a current NVMe Target configuration:
254 ./nvmetcli clear
256
258 nvmetcli has the ability to start and stop the NVMe Target
259 configuration on boot and shutdown through the systemctl Linux utility
260 via a .service file. nvmetcli package comes with nvmet.service which
261 when installed, it can automatically restore the default, saved NVMe
262 Target configuration from /etc/nvmet/config.json. nvmet.service can be
263 installed in directories such as /lib/systemd/system.
264 To explicitly enable the service, type:
266 systemctl enable nvmet
268 To explicitly disable the service, type:
270 systemctl disable nvmet
272 See also systemctl(1).
274
276 This man page was written by Jay Freyensee[1]. nvmetcli was originally
277 written by Christoph Hellwig[2].
278
280 Please send patches and bug reports to
281 linux-nvme@lists.infradead.org[3] for review and acceptance.
282
284 nvmetcli is licensed under the Apache License, Version 2.0. Software
285 distributed under this license is distributed on an "AS IS" BASIS,
286 WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either expressed or
287 implied.
288
290 1. Jay Freyensee
291 mailto:james.p.freyensee@intel.com
292 2. Christoph Hellwig
294 mailto:hch@infradead.org
295 3. linux-nvme@lists.infradead.org
297 mailto:linux-nvme@lists.infradead.org
298 05/11/2019 NVMETCLI(8)