1FENCED(8) cluster FENCED(8)
2
6 fenced - the I/O Fencing daemon
7
10 fenced [OPTIONS]
11
14 The fencing daemon, fenced, fences cluster nodes that have failed.
15 Fencing a node generally means rebooting it or otherwise preventing it
16 from writing to storage, e.g. disabling its port on a SAN switch.
17 Fencing involves interacting with a hardware device, e.g. network power
18 switch, SAN switch, storage array. Different "fencing agents" are run
19 by fenced to interact with various hardware devices.
20 Software related to sharing storage among nodes in a cluster, e.g. GFS,
22 usually requires fencing to be configured to prevent corruption of the
23 storage in the presence of node failure and recovery. GFS will not
24 allow a node to mount a GFS file system unless the node is running
25 fenced.
26 Once started, fenced waits for the fence_tool(8) join command to be
28 run, telling it to join the fence domain: a group of nodes that will
29 fence group members that fail. When the cluster does not have quorum,
30 fencing operations are postponed until quorum is restored. If a failed
31 fence domain member is reset and rejoins the cluster before the remain‐
32 ing domain members have fenced it, the fencing is no longer needed and
33 will be skipped.
34 fenced uses the corosync cluster membership system, it's closed process
36 group library (libcpg), and the cman quorum and configuration libraries
37 (libcman, libccs).
38 The cman init script usually starts the fenced daemon and runs
40 fence_tool join and leave.
41 Node failure
44 When a fence domain member fails, fenced runs an agent to fence it.
45 The specific agent to run and the agent parameters are all read from
46 the cluster.conf file (using libccs) at the time of fencing. The fenc‐
47 ing operation against a failed node is not considered complete until
48 the exec'ed agent exits. The exit value of the agent indicates the
49 success or failure of the operation. If the operation failed, fenced
50 will retry (possibly with a different agent, depending on the configu‐
51 ration) until fencing succeeds. Other systems such as DLM and GFS wait
52 for fencing to complete before starting their own recovery for a failed
53 node. Information about fencing operations will also appear in syslog.
54 When a domain member fails, the actual fencing operation can be delayed
56 by a configurable number of seconds (cluster.conf post_fail_delay or
57 -f). Within this time, the failed node could be reset and rejoin the
58 cluster to avoid being fenced. This delay is 0 by default to minimize
59 the time that other systems are blocked.
60 Domain startup
63 When the fence domain is first created in the cluster (by the first
64 node to join it) and subsequently enabled (by the cluster gaining quo‐
65 rum) any nodes listed in cluster.conf that are not presently members of
66 the corosync cluster are fenced. The status of these nodes is unknown,
67 and to be safe they are assumed to need fencing. This startup fencing
68 can be disabled, but it's only truly safe to do so if an operator is
69 present to verify that no cluster nodes are in need of fencing.
70 The following example illustrates why startup fencing is important.
72 Take a three node cluster with nodes A, B and C; all three have a GFS
73 file system mounted. All three nodes experience a low-level kernel
74 hang at about the same time. A watchdog triggers a reboot on nodes A
75 and B, but not C. A and B reboot, form the cluster again, gain quorum,
76 join the fence domain, _don't_ fence node C which is still hung and
77 unresponsive, and mount the GFS fs again. If C were to come back to
78 life, it could corrupt the fs. So, A and B need to fence C when they
79 reform the fence domain since they don't know the state of C. If C
80 _had_ been reset by a watchdog like A and B, but was just slow in
81 rebooting, then A and B might be fencing C unnecessarily when they do
82 startup fencing.
83 The first way to avoid fencing nodes unnecessarily on startup is to
85 ensure that all nodes have joined the cluster before any of the nodes
86 start the fence daemon. This method is difficult to automate.
87 A second way to avoid fencing nodes unnecessarily on startup is using
89 the cluster.conf post_join_delay setting (or -j option). This is the
90 number of seconds fenced will delay before actually fencing any victims
91 after nodes join the domain. This delay gives nodes that have been
92 tagged for fencing a chance to join the cluster and avoid being fenced.
93 A delay of -1 here will cause the daemon to wait indefinitely for all
94 nodes to join the cluster and no nodes will actually be fenced on
95 startup.
96 To disable fencing at domain-creation time entirely, the cluster.conf
98 clean_start setting (or -c option) can be used to declare that all
99 nodes are in a clean or safe state to start. This setting/option
100 should not generally be used since it risks not fencing a node that
101 needs it, which can lead to corruption in other applications (like GFS)
102 that depend on fencing.
103 Avoiding unnecessary fencing at startup is primarily a concern when
105 nodes are fenced by power cycling. If nodes are fenced by disabling
106 their SAN access, then unnecessarily fencing a node is usually less
107 disruptive.
108 Fencing override
111 If a fencing device fails, the agent may repeatedly return errors as
112 fenced tries to fence a failed node. In this case, the admin can manu‐
113 ally reset the failed node, and then use fence_ack_manual(8) to tell
114 fenced to continue without fencing the node.
115
118 Command line options override a corresponding setting in cluster.conf.
119 -D Enable debugging to stderr and don't fork.
122 See also fence_tool dump in fence_tool(8).
123 -L Enable debugging to log file.
125 See also logging in cluster.conf(5).
126 -g num groupd compatibility mode, 0 off, 1 on. Default 0.
128 -r path
130 Register a directory that needs to be empty for the daemon to
131 start. Use a dash (-) to skip default directories /sys/fs/gfs,
132 /sys/fs/gfs2, /sys/kernel/dlm.
133 -c All nodes are in a clean state to start. Do no startup fencing.
135 -s Skip startup fencing of nodes with no defined fence methods.
137 -q Disable dbus signals.
139 -j secs
141 Post-join fencing delay. Default 6.
142 -f secs
144 Post-fail fencing delay. Default 0.
145 -R secs
147 Number of seconds to wait for a manual override after a failed
148 fencing attempt before the next attempt. Default 3.
149 -O path
151 Location of a FIFO used for communication between fenced and
152 fence_ack_manual.
153 -h Print a help message describing available options, then exit.
155 -V Print program version information, then exit.
157
160 cluster.conf(5) is usually located at /etc/cluster/cluster.conf. It is
161 not read directly. Other cluster components load the contents into
162 memory, and the values are accessed through the libccs library.
163 Configuration options for fenced are added to the <fence_daemon /> sec‐
165 tion of cluster.conf, within the top level <cluster> section.
166 post_join_delay
169 is the number of seconds the daemon will wait before fencing any
170 victims after a node joins the domain. Default 6.
171 <fence_daemon post_join_delay="6"/>
173 post_fail_delay
176 is the number of seconds the daemon will wait before fencing any
177 victims after a domain member fails. Default 0.
178 <fence_daemon post_fail_delay="0"/>
180 clean_start
183 is used to prevent any startup fencing the daemon might do. It
184 indicates that the daemon should assume all nodes are in a clean
185 state to start. Default 0.
186 <fence_daemon clean_start="0"/>
188 override_path
191 is the location of a FIFO used for communication between fenced
192 and fence_ack_manual. Default shown.
193 <fence_daemon override_path="/var/run/cluster/fenced_override"/>
195 override_time
198 is the number of seconds to wait for administrator intervention
199 between fencing attempts following fence agent failures. Default
200 3.
201 <fence_daemon override_time="3"/>
203 Per-node fencing settings
206 The per-node fencing configuration is partly dependant on the specific
207 agent/hardware being used. The general framework begins like this:
208 <clusternodes>
210 <clusternode name="node1" nodeid="1">
212 <fence>
213 </fence>
214 </clusternode>
215 <clusternode name="node2" nodeid="2">
217 <fence>
218 </fence>
219 </clusternode>
220 </clusternodes>
222 The simple fragment above is a valid configuration: there is no way to
224 fence these nodes. If one of these nodes is in the fence domain and
225 fails, fenced will repeatedly fail in its attempts to fence it. The
226 admin will need to manually reset the failed node and then use
227 fence_ack_manual to tell fenced to continue without fencing it (see
228 override above).
229 There is typically a single method used to fence each node (the name
231 given to the method is not significant). A method refers to a specific
232 device listed in the separate <fencedevices> section, and then lists
233 any node-specific parameters related to using the device.
234 <clusternodes>
236 <clusternode name="node1" nodeid="1">
238 <fence>
239 <method name="1">
240 <device name="myswitch" foo="x"/>
241 </method>
242 </fence>
243 </clusternode>
244 <clusternode name="node2" nodeid="2">
246 <fence>
247 <method name="1">
248 <device name="myswitch" foo="y"/>
249 </method>
250 </fence>
251 </clusternode>
252 </clusternodes>
254 Fence device settings
257 This section defines properties of the devices used to fence nodes.
258 There may be one or more devices listed. The per-node fencing sections
259 above reference one of these fence devices by name.
260 <fencedevices>
262 <fencedevice name="myswitch" agent="..." something="..."/>
263 </fencedevices>
264 Multiple methods for a node
267 In more advanced configurations, multiple fencing methods can be
268 defined for a node. If fencing fails using the first method, fenced
269 will try the next method, and continue to cycle through methods until
270 one succeeds.
271 <clusternode name="node1" nodeid="1">
273 <fence>
274 <method name="1">
275 <device name="myswitch" foo="x"/>
276 </method>
277 <method name="2">
278 <device name="another" bar="123"/>
279 </method>
280 </fence>
281 </clusternode>
282 <fencedevices>
284 <fencedevice name="myswitch" agent="..." something="..."/>
285 <fencedevice name="another" agent="..."/>
286 </fencedevices>
287 Dual path, redundant power
290 Sometimes fencing a node requires disabling two power ports or two i/o
291 paths. This is done by specifying two or more devices within a method.
292 fenced will run the agent for the device twice, once for each device
293 line, and both must succeed for fencing to be considered successful.
294 <clusternode name="node1" nodeid="1">
296 <fence>
297 <method name="1">
298 <device name="sanswitch1" port="11"/>
299 <device name="sanswitch2" port="11"/>
300 </method>
301 </fence>
302 </clusternode>
303 When using power switches to fence nodes with dual power supplies, the
305 agents must be told to turn off both power ports before restoring power
306 to either port. The default off-on behavior of the agent could result
307 in the power never being fully disabled to the node.
308 <clusternode name="node1" nodeid="1">
310 <fence>
311 <method name="1">
312 <device name="nps1" port="11" action="off"/>
313 <device name="nps2" port="11" action="off"/>
314 <device name="nps1" port="11" action="on"/>
315 <device name="nps2" port="11" action="on"/>
316 </method>
317 </fence>
318 </clusternode>
319 Hardware-specific settings
322 Find documentation for configuring specific devices from the device
323 agent's man page.
324
327 fence_tool(8), fence_ack_manual(8), fence_node(8), cluster.conf(5)
328cluster 2009-12-21 FENCED(8)