1HISAXCTRL(8)              Linux System Administration             HISAXCTRL(8)
2
3
4

NAME

6       hisaxctrl - configure HiSax-Module
7

SYNOPSIS

9       hisaxctrl DriverId command parameters
10

DESCRIPTION

12       hisaxctrl  is used to setup the HiSax-ISDN device driver.  All logging-
13       output is sent to the device /dev/isdnctrl. So you can show it by  exe‐
14       cuting cat /dev/isdnctrl.
15       NOTE:   for   devfs   systems,   the  program  will  automatically  use
16       /dev/isdn/isdnctrl if available.
17
18       The use of hisaxctrl only makes  sense  if  you  are  using  the  HiSax
19       driver.
20

OPTIONS

22       DriverId
23              is  used  to  identify the card when using more than one passive
24              card. While loading the hisax module with  insmod,  or  modprobe
25              the  DriverId is set by appending id=idstring1%idstring2%...  to
26              the commandline.
27
28       command
29              is an integer selecting the setup category. The following values
30              are  defined  for  setting  the  logging-level of the HiSax-ISDN
31              device driver:
32
33               0 reports card status infos.
34               1 selects generic debugging.
35              11 selects layer 1 development debugging.
36              13 selects layer 3 development debugging.
37
38       the following commands are used to enable special features during  run‐
39       time of the HiSax-ISDN device driver.
40
41               2 set B-channel ON delay to parameter (in ms)
42               5 set B-channel in leased mode
43               6 set B-channel in TESTLOOP mode
44               7 set/reset card in Point To Point mode
45               8 set card in FIXED TEI mode
46               9 load firmware for DSP cards
47              10 set B-channel usage limit to 1 or 2 channels
48              12 set echo logging mode (only for some cards)
49                 B-channel usage limit needs to be 1 if enabled
50
51       parameter
52              If  the  command is 9 then the parameter is the full pathname to
53              the file containing the firmware.
54
55              For debug settings this is an integer  representing  a  bitmask.
56              Every  bit  in  this  mask  switches a debug facility on or off.
57              Depending on the selected category,  the  following  values  are
58              defined:
59
60              With generic debugging selected
61              (command 1):
62
63              0x001 Link-level <--> hardware-level communication
64              0x002 Top state machine
65              0x004 D-Channel Q.931 (call control messages)
66              0x008 D-Channel Q.921
67              0x010 B-Channel X.75
68              0x020 D-Channel l2
69              0x040 B-Channel l2
70              0x080 D-Channel link state debugging
71              0x100 B-Channel link state debugging
72              0x200 TEI debug
73              0x400 LOCK debug in callc.c
74              0x800 More debug in callc.c (not for normal use)
75
76              With layer 1 development debugging selected
77              (command 11):
78
79              0x001 Warnings (default: on)
80              0x002 IRQ status
81              0x004 ISAC
82              0x008 ISAC FIFO
83              0x010 HSCX
84              0x020 HSCX FIFO (attention: full B-Channel output!)
85              0x040 D-Channel LAPD frame types
86
87              With layer 3 development debugging selected
88              (command 13):
89
90              0x001 Warnings (default: on)
91              0x002 l3 protocol discriptor errors
92              0x004 l3 state machine
93              0x008 charge info debugging (1TR6)
94

EXAMPLE

96       hisaxctrl HiSax 1 0x3ff
97              enables full generic debugging.
98

AUTHOR

100       © 2000  by Karsten Keil <kkeil@suse.de>
101

SEE ALSO

103       isdnctrl(8), isdn_cause(7), isdninfo(4).
104
105
106
107isdn4k-utils-3.13                 2001/08/09                      HISAXCTRL(8)