1PG_RECVLOGICAL(1) PostgreSQL 10.7 Documentation PG_RECVLOGICAL(1)
2
6 pg_recvlogical - control PostgreSQL logical decoding streams
7
9 pg_recvlogical [option...]
10
12 pg_recvlogical controls logical decoding replication slots and streams
13 data from such replication slots.
14 It creates a replication-mode connection, so it is subject to the same
16 constraints as pg_receivewal(1), plus those for logical replication
17 (see Chapter 48).
18 pg_recvlogical has no equivalent to the logical decoding SQL
20 interface's peek and get modes. It sends replay confirmations for data
21 lazily as it receives it and on clean exit. To examine pending data on
22 a slot without consuming it, use pg_logical_slot_peek_changes.
23
25 At least one of the following options must be specified to select an
26 action:
27 --create-slot
29 Create a new logical replication slot with the name specified by
30 --slot, using the output plugin specified by --plugin, for the
31 database specified by --dbname.
32 --drop-slot
34 Drop the replication slot with the name specified by --slot, then
35 exit.
36 --start
38 Begin streaming changes from the logical replication slot specified
39 by --slot, continuing until terminated by a signal. If the server
40 side change stream ends with a server shutdown or disconnect, retry
41 in a loop unless --no-loop is specified.
42 The stream format is determined by the output plugin specified when
44 the slot was created.
45 The connection must be to the same database used to create the
47 slot.
48 --create-slot and --start can be specified together. --drop-slot
50 cannot be combined with another action.
51 The following command-line options control the location and format of
53 the output and other replication behavior:
54 -E lsn
56 --endpos=lsn
57 In --start mode, automatically stop replication and exit with
58 normal exit status 0 when receiving reaches the specified LSN. If
59 specified when not in --start mode, an error is raised.
60 If there's a record with LSN exactly equal to lsn, the record will
62 be output.
63 The --endpos option is not aware of transaction boundaries and may
65 truncate output partway through a transaction. Any partially output
66 transaction will not be consumed and will be replayed again when
67 the slot is next read from. Individual messages are never
68 truncated.
69 -f filename
71 --file=filename
72 Write received and decoded transaction data into this file. Use -
73 for stdout.
74 -F interval_seconds
76 --fsync-interval=interval_seconds
77 Specifies how often pg_recvlogical should issue fsync() calls to
78 ensure the output file is safely flushed to disk.
79 The server will occasionally request the client to perform a flush
81 and report the flush position to the server. This setting is in
82 addition to that, to perform flushes more frequently.
83 Specifying an interval of 0 disables issuing fsync() calls
85 altogether, while still reporting progress to the server. In this
86 case, data could be lost in the event of a crash.
87 -I lsn
89 --startpos=lsn
90 In --start mode, start replication from the given LSN. For details
91 on the effect of this, see the documentation in Chapter 48 and
92 Section 52.4. Ignored in other modes.
93 --if-not-exists
95 Do not error out when --create-slot is specified and a slot with
96 the specified name already exists.
97 -n
99 --no-loop
100 When the connection to the server is lost, do not retry in a loop,
101 just exit.
102 -o name[=value]
104 --option=name[=value]
105 Pass the option name to the output plugin with, if specified, the
106 option value value. Which options exist and their effects depends
107 on the used output plugin.
108 -P plugin
110 --plugin=plugin
111 When creating a slot, use the specified logical decoding output
112 plugin. See Chapter 48. This option has no effect if the slot
113 already exists.
114 -s interval_seconds
116 --status-interval=interval_seconds
117 This option has the same effect as the option of the same name in
118 pg_receivewal(1). See the description there.
119 -S slot_name
121 --slot=slot_name
122 In --start mode, use the existing logical replication slot named
123 slot_name. In --create-slot mode, create the slot with this name.
124 In --drop-slot mode, delete the slot with this name.
125 -v
127 --verbose
128 Enables verbose mode.
129 The following command-line options control the database connection
131 parameters.
132 -d database
134 --dbname=database
135 The database to connect to. See the description of the actions for
136 what this means in detail. This can be a libpq connection string;
137 see Section 33.1.1 for more information. Defaults to user name.
138 -h hostname-or-ip
140 --host=hostname-or-ip
141 Specifies the host name of the machine on which the server is
142 running. If the value begins with a slash, it is used as the
143 directory for the Unix domain socket. The default is taken from the
144 PGHOST environment variable, if set, else a Unix domain socket
145 connection is attempted.
146 -p port
148 --port=port
149 Specifies the TCP port or local Unix domain socket file extension
150 on which the server is listening for connections. Defaults to the
151 PGPORT environment variable, if set, or a compiled-in default.
152 -U user
154 --username=user
155 User name to connect as. Defaults to current operating system user
156 name.
157 -w
159 --no-password
160 Never issue a password prompt. If the server requires password
161 authentication and a password is not available by other means such
162 as a .pgpass file, the connection attempt will fail. This option
163 can be useful in batch jobs and scripts where no user is present to
164 enter a password.
165 -W
167 --password
168 Force pg_recvlogical to prompt for a password before connecting to
169 a database.
170 This option is never essential, since pg_recvlogical will
172 automatically prompt for a password if the server demands password
173 authentication. However, pg_recvlogical will waste a connection
174 attempt finding out that the server wants a password. In some cases
175 it is worth typing -W to avoid the extra connection attempt.
176 The following additional options are available:
178 -V
180 --version
181 Print the pg_recvlogical version and exit.
182 -?
184 --help
185 Show help about pg_recvlogical command line arguments, and exit.
186
188 This utility, like most other PostgreSQL utilities, uses the
189 environment variables supported by libpq (see Section 33.14).
190
192 See Section 48.1 for an example.
193
195 pg_receivewal(1)
196PostgreSQL 10.7 2019 PG_RECVLOGICAL(1)