1INXI(1) inxi manual INXI(1)
2
6 inxi - Command line system information script for console and IRC
7
9 inxi
10 inxi [-AbBCdDfFGhiIlmMnNopPrRsSuUVwzZ]
12 inxi [-c NUMBER] [-t [c|m|cm|mc][NUMBER]] [-v NUMBER] [-W LOCATION]
14 [--weather-unit {m|i|mi|im}] [-y WIDTH] inxi [--memory-modules] [--mem‐
15 ory-short] [--recommends] [--slots] [--usb]
16 inxi [-x|-xx|-xxx|-a|--admin] -OPTION(s)
18 All options have long form variants - see below for these and more
20 advanced options.
21
24 inxi is a command line system information script built for console and
25 IRC. It is also used a debugging tool for forum technical support to
26 quickly ascertain users' system configurations and hardware. inxi shows
27 system hardware, CPU, drivers, Xorg, Desktop, Kernel, gcc version(s),
28 Processes, RAM usage, and a wide variety of other useful information.
29 inxi output varies depending on whether it is being used on CLI or IRC,
31 with some default filters and color options applied only for IRC use.
32 Script colors can be turned off if desired with -c 0, or changed using
33 the -c color options listed in the STANDARD OPTIONS section below.
34
37 In order to maintain basic privacy and security, inxi used on IRC auto‐
38 matically filters out your network device MAC address, WAN and LAN IP,
39 your /home username directory in partitions, and a few other items.
40 Because inxi is often used on forums for support, you can also trigger
42 this filtering with the -z option (-Fz, for example). To override the
43 IRC filter, you can use the -Z option. This can be useful in debugging
44 network connection issues online in a private chat, for example.
45
48 Options can be combined if they do not conflict. You can either group
49 the letters together or separate them.
50 Letters with numbers can have no gap or a gap at your discretion,
52 except when using -t.
53 For example: inxi -AG or inxi -A -G or inxi -c10
55 Note that all the short form options have long form equivalents, which
57 are listed below. However, usually the short form is used in examples
58 in order to keep things simple.
59
62 -A, --audio
63 Show Audio/sound card(s) information, including card driver.
64 -b, --basic
66 Show basic output, short form. Same as: inxi -v 2
67 -B, --battery
69 Show system battery (ID-x) data, charge, condition, plus extra
70 information (if battery present). Uses /sys or, for BSDs without
71 systctl battery data, dmidecode. dmidecode does not have very
72 much information, and none about current battery
73 state/charge/voltage. Supports multiple batteries when using
74 /sys data.
75 Note that for charge, the output shows the current charge, as
77 well as its value as a percentage of the available capacity,
78 which can be less than the original design capacity. In the fol‐
79 lowing example, the actual current available capacity of the
80 battery is 22.2 Wh.
81 charge: 20.1 Wh 95.4%
83 The condition item shows the remaining available capacity /
85 original design capacity, and then this figure as a percentage
86 of original capacity available in the battery.
87 condition: 22.2/36.4 Wh (61%)
89 With -x shows attached Device-x information (mouse, keyboard,
91 etc.) if they are battery powered.
92 -c, --color [0-42]
95 Set color scheme. If no scheme number is supplied, 0 is assumed.
96 -c [94-99]
99 These color selectors run a color selector option prior to inxi
101 starting which lets you set the config file value for the selec‐
102 tion.
103 NOTE: All configuration file set color values are removed when
105 output is piped or redirected. You must use the explicit runtime
106 -c <color number> option if you want color codes to be present
107 in the piped/redirected output.
108 Color selectors for each type display (NOTE: IRC and global only
110 show safe color set):
111 -c 94 - Console, out of X.
113 -c 95 - Terminal, running in X - like xTerm.
115 -c 96 - GUI IRC, running in X - like XChat, Quassel, Konversation etc.
117 -c 97 - Console IRC running in X - like irssi in xTerm.
119 -c 98 - Console IRC not in X.
121 -c 99 - Global - Overrides/removes all settings.
123 Setting a specific color type removes the global color selec‐
125 tion.
126 -C, --cpu
128 Show full CPU output, including per CPU clock speed and CPU max
129 speed (if available). If max speed data present, shows (max) in
130 short output formats (inxi, inxi -b) if actual CPU speed matches
131 max CPU speed. If max CPU speed does not match actual CPU speed,
132 shows both actual and max speed information. See -x for more
133 options.
134 For certain CPUs (some ARM, and AMD Zen family) shows CPU die
136 count.
137 The details for each CPU include a technical description e.g.
139 type: MT MCP
140 * MT - Multi/Hyper Threaded CPU, more than 1 thread per core
142 (previously HT).
143 * MCM - Multi Chip Model (more than 1 die per CPU).
145 * MCP - Multi Core Processor (more than 1 core per CPU).
147 * SMP - Symmetric Multi Processing (more than 1 physical CPU).
149 * UP - Uni (single core) Processor.
151 -d, --disk-full,--optical
154 Show optical drive data as well as -D hard drive data. With -x,
155 adds a feature line to the output. Also shows floppy disks if
156 present. Note that there is no current way to get any informa‐
157 tion about the floppy device that I am aware of, so it will sim‐
158 ply show the floppy ID without any extra data. -xx adds a few
159 more features.
160 -D, --disk
162 Show Hard Disk info. Shows total disk space and used percentage.
163 The disk used percentage includes space used by swap parti‐
164 tion(s), since those are not usable for data storage. Note that
165 with RAID disks, the percentage will be wrong since the total is
166 computed from the disk sizes, but used is computed from mounted
167 partition used percentages. This small defect may get corrected
168 in the future. Also, unmounted partitions are not counted in
169 disk use percentages since inxi has no access to the used
170 amount.
171 Also shows per disk information: Disk ID, type (if present),
173 vendor (if detected), model, and size. See Extra Data Options
174 for more features.
175 -f, --flags
177 Show all CPU flags used, not just the short list. Not shown with
178 -F in order to avoid spamming. ARM CPUs: show features items.
179 -F, --full
181 Show Full output for inxi. Includes all Upper Case line letters
182 except -W, plus -s and -n. Does not show extra verbose options
183 such as -d -f -i -l -m -o -p -r -t -u -x unless you use those
184 arguments in the command, e.g.: inxi -Frmxx
185 -G, --graphics
187 Show Graphic card(s) information, including details of card and
188 card driver, display protocol (if available), display server
189 (vendor and version number), e.g.:
190 Display: x11 server: Xorg 1.15.1
192 If protocol is not detected, shows:
194 Display: server: Xorg 1.15.1
196 Also shows screen resolution(s), OpenGL renderer, OpenGL core
198 profile version/OpenGL version.
199 Compositor information will show if detected using -xx option.
201 -h, --help
203 The help menu. Features dynamic sizing to fit into terminal win‐
204 dow. Set script global COLS_MAX_CONSOLE if you want a different
205 default value, or use -y <width> to temporarily override the
206 defaults or actual window width.
207 -i, --ip
209 Show WAN IP address and local interfaces (latter requires ifcon‐
210 fig or ip network tool), as well as network output from -n. Not
211 shown with -F for user security reasons. You shouldn't paste
212 your local/WAN IP. Shows both IPv4 and IPv6 link IP addresses.
213 -I, --info
216 Show Information: processes, uptime, memory, IRC client (or
217 shell type if run in shell, not IRC), inxi version. See -x and
218 -xx for extra information (init type/version, runlevel).
219 Note: if -m is used or triggered, the memory item will show in
221 the main Memory: report of -m, not in Info:.
222 Rasberry Pi only: uses vcgencmd get_mem gpu to get gpu RAM
224 amount, if user is in video group and vcgencmd is installed.
225 Uses this result to increase the Memory: amount and used:
226 amounts.
227 -l, --label
229 Show partition labels. Default: main partitions -P. For full -p
230 output, use: -pl.
231 -m, --memory
233 Memory (RAM) data. Does not display with -b or -F unless you
234 use -m explicitly. Ordered by system board physical system mem‐
235 ory array(s) (Array-[number]), and individual memory devices
236 (Device-[number]). Physical memory array data shows array
237 capacity, number of devices supported, and Error Correction
238 information. Devices shows locator data (highly variable in syn‐
239 tax), size, speed, type (eg: type: DDR3).
240 Note: -m uses dmidecode, which must be run as root (or start
242 inxi with sudo), unless you figure out how to set up sudo to
243 permit dmidecode to read /dev/mem as user. speed and bus width
244 will not show if No Module Installed is found in size.
245 Note: If -m is triggered RAM total/used report will appear in
247 this section, not in -I or -tm items.
248 Because dmidecode data is extremely unreliable, inxi will try to
250 make best guesses. If you see (check) after the capacity num‐
251 ber, you should check it with the specifications. (est) is
252 slightly more reliable, but you should still check the real
253 specifications before buying RAM. Unfortunately there is nothing
254 inxi can do to get truly reliable data about the system RAM;
255 maybe one day the kernel devs will put this data into /sys, and
256 make it real data, taken from the actual system, not dmi data.
257 For most people, the data will be right, but a significant per‐
258 centage of users will have either a wrong max module size, if
259 present, or max capacity.
260 See --memory-modules and --memory-short if you want a shorter
262 report.
263 --memory-modules
265 Memory (RAM) data. Show only RAM arrays and modules in Memory
266 report. Skip empty slots. See -m.
267 --memory-short
269 Memory (RAM) data. Show a one line RAM report in Memory, e.g.
270 Report: arrays: 1 slots: 4 modules: 2 type: DDR4 See -m.
271 -M, --machine
273 Show machine data. Device, Motherboard, BIOS, and if present,
274 System Builder (Like Lenovo). Older systems/kernels without the
275 required /sys data can use dmidecode instead, run as root. If
276 using dmidecode, may also show BIOS/UEFI revision as well as
277 version. --dmidecode forces use of dmidecode data instead of
278 /sys. Will also attempt to show if the system was booted by
279 BIOS, UEFI, or UEFI [Legacy], the latter being legacy BIOS boot
280 mode in a system board using UEFI.
281 Device information requires either /sys or dmidecode. Note that
283 'other-vm?' is a type that means it's usually a VM, but inxi
284 failed to detect which type, or positively confirm which VM it
285 is. Primary VM identification is via systemd-detect-virt but
286 fallback tests that should also support some BSDs are used. Less
287 commonly used or harder to detect VMs may not be correctly
288 detected. If you get an incorrect output, post an issue and
289 we'll get it fixed if possible.
290 Due to unreliable vendor data, device type will show: desktop,
292 laptop, notebook, server, blade, plus some obscure stuff that
293 inxi is unlikely to ever run on.
294 -n, --network-advanced
296 Show Advanced Network card information in addition to that pro‐
297 duced by -N. Shows interface, speed, MAC ID, state, etc.
298 -N, --network
300 Show Network card(s) information, including card driver. With
301 -x, shows PCI BusID, Port number.
302 -o, --unmounted
304 Show unmounted partition information (includes UUID and LABEL if
305 available). Shows file system type if you have lsblk installed
306 (Linux only). For BSD/GNU Linux: shows file system type if file
307 is installed, and if you are root or if you have added to
308 /etc/sudoers (sudo v. 1.7 or newer):
309 <username> ALL = NOPASSWD: /usr/bin/file (sample)
311 Does not show components (partitions that create the md-raid
313 array) of md-raid arrays.
314 -p, --partitions-full
316 Show full Partition information (-P plus all other detected
317 mounted partitions).
318 -P, --partitions
320 Show basic Partition information. Shows, if detected: / /boot
321 /home /opt /tmp /usr /usr/home /var /var/tmp /var/log. Use -p
322 to see all mounted partitions.
323 -r, --repos
325 Show distro repository data. Currently supported repo types:
326 APK (Alpine Linux + derived versions)
328 APT (Debian, Ubuntu + derived versions, as well as RPM based APT
330 distros like PCLinuxOS or Alt-Linux)
331 CARDS (NuTyX + derived versions)
333 EOPKG (Solus)
335 PACMAN (Arch Linux, KaOS + derived versions)
337 PACMAN-G2 (Frugalware + derived versions)
339 PISI (Pardus + derived versions)
341 PORTAGE (Gentoo, Sabayon + derived versions)
343 PORTS (OpenBSD, FreeBSD, NetBSD + derived OS types)
345 SLACKPKG (Slackware + derived versions)
347 TCE (TinyCore)
349 URPMQ (Mandriva, Mageia + derived versions)
351 XBPS (Void)
353 YUM/ZYPP (Fedora, Red Hat, Suse + derived versions)
355 More will be added as distro data is collected. If yours is
357 missing please show us how to get this information and we'll try
358 to add it.
359 -R, --raid
361 Show RAID data. Shows RAID devices, states, levels and compo‐
362 nents, and extra data with -x / -xx.
363 md-raid: If device is resyncing, also shows resync progress
365 line.
366 Note: Only md-raid and ZFS are currently supported. Other soft‐
368 ware RAID types could be added, but only if users supply all
369 data required, and if the software RAID actually can be made to
370 give the required output.
371 If hardware RAID is detected, shows basic information. Due to
373 complexity of adding hardware RAID device disk / RAID reports,
374 those will only be added if there is demand, and reasonable
375 reporting tools.
376 --recommends
379 Checks inxi application dependencies and recommends, as well as
380 directories, then shows what package(s) you need to install to
381 add support for each feature.
382 -s, --sensors
384 Show output from sensors if sensors installed/configured: Moth‐
385 erboard/CPU/GPU temperatures; detected fan speeds. GPU tempera‐
386 ture when available. Nvidia shows screen number for multiple
387 screens. IPMI sensors are also used (root required) if present.
388 --slots
390 Show PCI slots with type, speed, and status information.
391 -S, --system
393 Show System information: host name, kernel, desktop environment
394 (if in X), distro. With -xx show dm - or startx - (only shows if
395 present and running if out of X), and if in X, with -xxx show
396 more desktop info, e.g. taskbar or panel.
397 -t, --processes
399 [c|m|cm|mc NUMBER] Show processes. If no arguments, defaults to
400 cm. If followed by a number, shows that number of processes for
401 each type (default: 5; if in IRC, max: 5)
402 Make sure that there is no space between letters and numbers
404 (e.g. write as -t cm10).
405 -t c - CPU only. With -x, also shows memory for that process on same
407 line.
408 -t m - memory only. With -x, also shows CPU for that process on same
410 line. If the -I line is not triggered, will also show the sys‐
411 tem RAM used/total information.
412 -t cm - CPU+memory. With -x, shows also CPU or memory for that process
414 on same line.
415 --usb Show USB data for attached Hubs and Devices. Hubs also show num‐
418 ber of ports. Be aware that a port is not always external, some
419 may be internal, and either used or unused (for example, a moth‐
420 erboard USB header connector that is not used).
421 Hubs and Devices are listed in order of BusID.
423 BusID is generally in this format: BusID-
425 port[.port][.port]:DeviceID
426 Device ID is a number created by the kernel, and has no neces‐
428 sary ordering or sequence connection, but can be used to match
429 this output to lsusb values, which generally shows BusID / Devi‐
430 ceID (except for tree view, which shows ports).
431 Examples: Device-3: 4-3.2.1:2 or Hub: 4-0:1
433 The rev: 2.0 item refers to the USB revision number, like 1.0 or
435 3.1.
436 -u, --uuid
439 Show partition UUIDs. Default: main partitions -P. For full -p
440 output, use: -pu.
441 -U, --update
443 Note - Maintainer may have disabled this function.
444 If inxi -h has no listing for -U then it's disabled.
446 Auto-update script. Note: if you installed as root, you must be
448 root to update, otherwise user is fine. Also installs / updates
449 this man page to: /usr/local/share/man/man1 (if
450 /usr/local/share/man/ exists AND there is no inxi man page in
451 /usr/share/man/man1, otherwise it goes to /usr/share/man/man1).
452 This requires that you be root to write to that directory. See
453 --man or --no-man to force or disable man install.
454 -V, --version
457 inxi version information. Prints information then exits.
458 -v, --verbosity
460 Script verbosity levels. If no verbosity level number is given,
461 0 is assumed. Should not be used with -b or -F.
462 Supported levels: 0-8 Examples : inxi -v 4 or inxi -v4
464 -v 0 - Short output, same as: inxi
466 -v 1 - Basic verbose, -S + basic CPU (cores, type, clock speed, and
468 min/max speeds, if available) + -G + basic Disk + -I.
469 -v 2 - Adds networking card (-N), Machine (-M) data, Battery (-B) (if
471 available). Same as: inxi -b
472 -v 3 - Adds advanced CPU (-C) and network (-n) data; triggers -x
474 advanced data option.
475 -v 4 - Adds partition size/used data (-P) for (if present): / /home
477 /var/ /boot. Shows full disk data (-D)
478 -v 5 - Adds audio card (-A), memory/RAM (-m), sensors (-s), partition
480 label (-l), UUID (-u), and short form of optical drives.
481 -v 6 - Adds full mounted partition data (-p), unmounted partition
483 data (-o), optical drive data (-d), USB (--usb); triggers -xx
484 extra data option.
485 -v 7 - Adds network IP data (-i); triggers -xxx
487 -v 8 - All system data available. Adds Repos (-r), PCI slots
489 (--slots), processes (-tcm), admin (--admin). Useful for testing
490 output and to see what data you can get from your system.
491 -w, --weather
493 Adds weather line. To get weather for an alternate location, use
494 -W [location]. See also -x, -xx, -xxx options. Please note that
495 your distribution's maintainer may chose to disable this fea‐
496 ture.
497 DO NOT USE THIS FEATURE FOR AUTOMATED WEATHER UPDATES! You will
499 be blocked from any further access. This feature is not meant
500 for widget type weather monitoring, or Conky type use. It is
501 meant to get weather when you need to see it, for example, on a
502 remote server.
503 -W, --weather-location <location_string>
505 Get weather/time for an alternate location. Accepts postal/zip
506 code[, country], city,state pair, or latitude,longitude. Note:
507 city/country/state names must not contain spaces. Replace spaces
508 with '+' sign. Don't place spaces around any commas. Postal code
509 is not reliable except for North America and maybe the UK. Try
510 postal codes with and without country code added. Note that
511 City,State applies only to USA, otherwise it's City,Country. If
512 country name (english) does not work, try 2 character country
513 code (e.g. Spain: es; Great Britain: gb).
514 See https://en.wikipedia.org/wiki/ISO_3166-1_alpha-2 for current
516 2 letter country codes.
517 Use only ASCII letters in city/state/country names.
519 Examples: -W 95623,us OR -W Boston,MA OR -W 45.5234,-122.6762 OR
521 -W new+york,ny OR -W bodo,norway.
522 DO NOT USE THIS FEATURE FOR AUTOMATED WEATHER UPDATES! Use of
524 automated queries, will result in your access being blocked. If
525 you try to work around the ban, you will be permanently banned
526 from this service.
527 --weather-source, --ws <unit>
529 [1-9] Switches weather data source. Possible values are 1-9. 1-4
530 will generally be active, and 5-9 may or may not be active, so
531 check. 1 may not support city / country names with spaces (even
532 if you use the + sign instead of space). 2 offers pretty good
533 data, but may not have all small city names for -W.
534 Please note that the data sources are not static per value, and
536 can change any time, or be removed, so always test to verify
537 which source is being used for each value if that is important
538 to you. Data sources may be added or removed on occasions, so
539 try each one and see which you prefer. If you get unsupported
540 source message, it means that number has not been implemented.
541 --weather-unit <unit>
543 [m|i|mi|im] Sets weather units to metric (m), imperial (i), met‐
544 ric (imperial) (mi, default), imperial (metric) (im). If metric
545 or imperial not found,sets to default value, or N/A.
546 -y, --width <integer>
548 This is an absolute width override which sets the output line
549 width max. Overrides COLS_MAX_IRC / COLS_MAX_CONSOLE globals,
550 or the actual widths of the terminal. 80 is the minimum width
551 supported. -1 removes width limits. Example: inxi -Fxx -y 130
552 -z, --filter
554 Adds security filters for IP addresses, serial numbers, MAC,
555 location (-w), and user home directory name. On by default for
556 IRC clients.
557 -Z, --filter-override
559 Absolute override for output filters. Useful for debugging net‐
560 working issues in IRC for example.
561
563 These options can be triggered by one or more -x. Alternatively, the
564 -v options trigger them in the following way: -v 3 adds -x; -v 6 adds
565 -xx; -v 7 adds -xxx
566 These extra data triggers can be useful for getting more in-depth data
568 on various options. They can be added to any long form option list,
569 e.g.: -bxx or -Sxxx
570 There are 3 extra data levels:
572 -x, -xx, -xxx
574 OR
576 --extra 1, --extra 2, --extra 3
578 The following details show which lines / items display extra informa‐
580 tion for each extra data level.
581 -x -A - Adds (if available and/or relevant) vendor: item, which shows
583 specific vendor [product] information.
584 - Adds version/port(s)/driver version (if available) for each
586 Audio device.
587 - Adds PCI Bus ID/USB ID number of each Audio device.
589 -x -B - Adds vendor/model, battery status (if battery present).
591 - Adds attached battery powered peripherals (Device-[number]:)
593 if detected (keyboard, mouse, etc.).
594 -x -C - Adds bogomips on CPU (if available)
596 - Adds CPU Flags (short list). Use -f to see full flag/feature
598 list.
599 - Adds CPU microarchitecture + revision (e.g. Sandy Bridge, K8,
601 ARMv8, P6, etc.). Only shows data if detected. Newer microarchi‐
602 tectures will have to be added as they appear, and require the
603 CPU family ID and model ID.
604 Examples: arch: Sandy Bridge rev: 2, arch: K8 rev.F+ rev: 2
606 -x -d - Adds more items to Features line of optical drive; dds rev
608 version to optical drive.
609 -x -D - Adds HDD temperature with disk data if you have hddtemp
611 installed, if you are root or if you have added to /etc/sudoers
612 (sudo v. 1.7 or newer):
613 <username> ALL = NOPASSWD: /usr/sbin/hddtemp (sample)
615 -x -G - Adds (if available and/or relevant) vendor: item, which shows
617 specific vendor [product] information.
618 - Adds direct rendering status.
620 - Adds (for single GPU, nvidia driver) screen number that GPU is
622 running on.
623 - Adds PCI Bus ID/USB ID number of each Graphics card.
625 -x -i - Adds IP v6 additional scope data, like Global, Site, Temporary
627 for each interface.
628 Note that there is no way I am aware of to filter out the depre‐
630 cated IP v6 scope site/global temporary addresses from the out‐
631 put of ifconfig. The ip tool shows that clearly.
632 ip-v6-temporary - (ip tool only), scope global temporary. Scope
634 global temporary deprecated is not shown
635 ip-v6-global - scope global (ifconfig will show this for all
637 types, global, global temporary, and global temporary depre‐
638 cated, ip shows it only for global)
639 ip-v6-link - scope link (ip/ifconfig) - default for -i.
641 ip-v6-site - scope site (ip/ifconfig). This has been deprecated
643 in IPv6, but still exists. ifconfig may show multiple site val‐
644 ues, as with global temporary, and global temporary deprecated.
645 ip-v6-unknown - unknown scope
647 -x -I - Adds current init system (and init rc in some cases, like
650 OpenRC). With -xx, shows init/rc version number, if available.
651 - Adds default system gcc. With -xx, also show other installed
653 gcc versions.
654 - Adds current runlevel (not available with all init systems).
656 - If in shell (i.e. not in IRC client), adds shell version num‐
658 ber, if available.
659 -x -m, --memory-modules
661 - If present, adds maximum memory module/device size in the
662 Array line. Only some systems will have this data available.
663 Shows estimate if it can generate one.
664 - Adds device type in the Device line.
666 -x -N - Adds (if available and/or relevant) vendor: item, which shows
668 specific vendor [product] information.
669 - Adds version/port(s)/driver version (if available) for each
671 Network card;
672 - Adds PCI Bus ID/USB ID number of each Network card.
674 -x -R - md-raid: Adds second RAID Info line with extra data: blocks,
676 chunk size, bitmap (if present). Resync line, shows blocks
677 synced/total blocks.
678 - Hardware RAID: Adds driver version, bus ID.
680 -x -s - Adds basic voltages: 12v, 5v, 3.3v, vbat (ipmi, lm-sensors if
682 present).
683 -x -S - Adds Kernel gcc version.
685 - Adds to Distro: base: if detected. System base will only be
687 seen on a subset of distributions. The distro must be both
688 derived from a parent distro (e.g. Mint from Ubuntu), and
689 explicitly added to the supported distributions for this fea‐
690 ture. Due to the complexity of distribution identification,
691 these will only be added as relatively solid methods are found
692 for each distribution system base detection.
693 -x -t - Adds memory use output to CPU (-xt c), and CPU use to memory
695 (-xt m).
696 -x --usb
698 - For Devices, adds driver(s).
699 -x -w, -W
701 - Adds humidity and barometric pressure.
702 - Adds wind speed and direction.
704 -xx -A - Adds vendor:product ID for each Audio device.
706 -xx -B - Adds serial number, voltage (if available). Note that volts
708 shows the data (if available) as the voltage now / minimum
709 design voltage.
710 -xx -C - Adds L1 cache: and L3 cache: if either are available. Requires
712 dmidecode and sudo/root.
713 -xx -D - Adds disk serial number.
715 - Adds disk speed (if available). This is the theoretical top
717 speed of the device as reported. This speed may be restricted by
718 system board limits, eg. a SATA 3 drive on a SATA 2 board may
719 report SATA 2 speeds, but this is not completely consistent,
720 sometimes a SATA 3 device on a SATA 2 board reports its design
721 speed.
722 NVMe drives: adds lanes, and (per direction) speed is calculated
724 with lane speed * lanes * PCIe overhead. PCIe 1 and 2 have data
725 rates of GT/s * .8 = Gb/s (10 bits required to transfer 8 bits
726 of data). PCIe 3 and greater transfer data at a rate of GT/s *
727 128/130 * lanes = Gb/s (130 bits required to transfer 128 bits
728 of data).
729 For a PCIe 3 NVMe drive, with speed of 8 GT/s and 4 lanes (8GT/s
731 * 128/130 * 4 = 31.6 Gb/s):
732 speed: 31.6 Gb/s lanes: 4
734 -xx -G - Adds vendor:product ID of each Graphics card.
736 - Adds compositor, if found (experimental).
738 - For free drivers, adds OpenGL compatibility version number if
740 available. For nonfree drivers, the core version and compati‐
741 bility versions are usually the same. Example:
742 v: 3.3 Mesa 11.2.0 compat-v: 3.0
744 - If available, shows alternate: Xorg drivers. This means a
746 driver on the default list of drivers Xorg automatically checks
747 for the card, but which is not installed. For example, if you
748 have nouveau driver, nvidia would show as alternate if it was
749 not installed. Note that alternate: does NOT mean you should
750 have it, it's just one of the drivers Xorg checks to see if is
751 present and loaded when checking the card. This can let you know
752 there are other driver options. Note that if you have explic‐
753 itly set the driver in xorg.conf, Xorg will not create this
754 automatic check driver list.
755 -xx -I - Adds init type version number (and rc if present).
758 - Adds other detected installed gcc versions (if present).
760 - Adds system default runlevel, if detected. Supports Sys‐
762 temd/Upstart/SysVinit type defaults.
763 - Adds parent program (or tty) that started shell, if not IRC
765 client.
766 -xx -m, --memory-modules
768 - Adds memory device Manufacturer.
769 - Adds memory device Part Number (part-no:). Useful for order‐
771 ing new or replacement memory sticks etc. Part numbers are
772 unique, particularly if you use the word memory in the search as
773 well. With -xxx, also shows serial number.
774 - Adds single/double bank memory, if data is found. Note, this
776 may not be 100% right all of the time since it depends on the
777 order that data is found in dmidecode output for type 6 and type
778 17.
779 -xx -M - Adds chassis information, if data is available. Also shows
781 BIOS ROM size if using dmidecode.
782 -xx -N - Adds vendor:product ID for each Network card.
784 -xx -R - md-raid: Adds superblock (if present) and algorithm. If
786 resync, shows progress bar.
787 - Hardware RAID: Adds Chip vendor:product ID.
789 -xx -s - Adds DIMM/SOC voltages, if present (ipmi only).
791 -xx -S - Adds display manager (dm) type, if present. If none, shows
793 N/A. Supports most known display managers, including gdm, gdm3,
794 idm, kdm, lightdm, lxdm, mdm, nodm, sddm, slim, tint, wdm, and
795 xdm.
796 - Adds, if run in X, window manager type (wm), if available.
798 Not all window managers are supported. Some desktops support
799 using more than one window manager, so this can be useful to see
800 what window manager is actually running. If none found, shows
801 nothing. Uses a less accurate fallback tool wmctrl if ps tests
802 fail to find data.
803 - Adds desktop toolkit (tk), if available (Xfce/KDE/Trinity).
805 -xx --slots
807 - Adds slot length.
808 -xx --usb
810 - Adds vendor:chip id.
811 -xx -w, -W
813 - Adds wind chill, heat index, and dew point, if available.
814 - Adds cloud cover, rain, snow, or precipitation (amount in pre‐
816 vious hour to observation time), if available.
817 -xxx -A
819 - Adds, if present, serial number.
820 -xxx -B
822 - Adds battery chemistry (e.g. Li-ion), cycles (NOTE: there
823 appears to be a problem with the Linux kernel obtaining the
824 cycle count, so this almost always shows 0. There's nothing that
825 can be done about this glitch, the data is simply not available
826 as of 2018-04-03), location (only available from dmidecode
827 derived output).
828 - Adds attached device rechargeable: [yes|no] information.
830 -xxx -C
832 - Adds boost: [enabled|disabled] if detected, aka turbo. Not all
833 CPUs have this feature.
834 -xxx -D
836 - Adds disk firmware revision number (if available).
837 - Adds disk partition scheme (in most cases), e.g. scheme: GPT.
839 Currently not able to detect all schemes, but handles the most
840 common, e.g. GPT or MBR.
841 - Adds disk rotation speed (in some but not all cases), e.g.
843 rotation: 7200 rpm. Only appears if detected (SSD drives do not
844 have rotation speeds, for example). If none found, nothing
845 shows. Not all disks report this speed, so even if they are
846 spinnning, no data will show.
847 -xxx -G
849 - Adds (if available) compositor: version v:.
850 -xxx -I
852 - For Shell: adds (su|sudo|login) to shell name if present.
853 - For running in: adds (SSH) to parent, if present. SSH detec‐
855 tion uses the who am i test.
856 -xxx -m, --memory-modules
858 - Adds memory bus width: primary bus width, and if present,
859 total width. e.g. bus width: 64 bit (total: 72 bits). Note that
860 total / data widths are mixed up sometimes in dmidecode output,
861 so inxi will take the larger value as the total if present. If
862 no total width data is found, then inxi will not show that item.
863 - Adds device Type Detail, e.g. detail: DDR3 (Synchronous).
865 - Adds, if present, memory module voltage. Only some systems
867 will have this data available.
868 - Adds device serial number.
870 -xxx -N
872 - Adds, if present, serial number.
873 -xxx -R
875 - md-raid: Adds system mdraid support types (kernel support,
876 read ahead, RAID events)
877 - zfs-raid: Adds portion allocated (used) by RAID array/device.
879 - Hardware RAID: Adds rev, ports, and (if available and/or rele‐
881 vant) vendor: item, which shows specific vendor [product] infor‐
882 mation.
883 -xxx -S
885 - Adds, if in X, or with --display, bar/dock/panel/tray items
886 (info). If none found, shows nothing. Supports desktop items
887 like gnome-panel, lxpanel, xfce4-panel, lxqt-panel, tint2,
888 cairo-dock, trayer, and many others.
889 - Adds (if present), window manager (wm) version number.
891 - Adds (if present), display manager (dm) version number.
893 -xxx --usb
895 - Adds, if present, serial number for non hub devices.
896 - Adds interfaces: for non hub devices.
898 - Adds, if available, USB speed in Mbits/s or Gbits/s.
900 -xxx -w, -W
902 - Adds location (city state country), observation altitude (if
903 available), weather observation time (if available), sunset/sun‐
904 rise (if available).
905
908 These options are triggered with --admin or -a. Admin options are
909 advanced output options, and are more technical, and mostly of interest
910 to system administrators or other machine admins. The --admin option
911 only has to be used once, and will trigger the following features.
912 -a -C - Adds CPU family, model-id, and stepping (replaces rev of -Cx).
914 Format is hexadecimal (decimal) if greater than 9, otherwise
915 hexadecimal.
916 - Adds CPU microcode. Format is hexadecimal.
918 - Adds CPU Vulnerabilities (bugs) as known by your current ker‐
920 nel. Lists by Type: ... (status|mitigation): .... for systems
921 that support this feature (Linux kernel 4.14 or newer, or
922 patched older kernels).
923 -a -d,-a -D
926 - Adds logical and physical block size in bytes.
927 -a -p,-a -P
930 - Adds raw partition size, including file system overhead, par‐
931 tition table, e.g.
932 raw size: 60.00 GiB.
934 - Adds percent of raw size available to size: item, e.g.
936 size: 58.81 GiB (98.01%).
938 Note that used: 16.44 GiB (34.3%) percent refers to the avail‐
940 able size, not the raw size.
941 - Adds partition filesystem block size if found (requires root
943 and blockdev).
944 - For swap, adds swappiness and vfs cache pressure, and a mes‐
946 sage to indicate if it is the default value or not (Linux only,
947 and only if available). If not, shows default value as well,
948 e.g.
949 swappiness: 60 (default) cache pressure: 90 (default 100).
951 -a -S - Adds kernel boot parameters to Kernel section (if detected).
954 Support varies by OS type.
955
958 --alt 40
959 Bypass Perl as a downloader option. Priority is: Perl
960 (HTTP::Tiny), Curl, Wget, Fetch, (OpenBSD only) ftp.
961 --alt 41
964 Bypass Curl as a downloader option. Priority is: Perl
965 (HTTP::Tiny), Curl, Wget, Fetch, (OpenBSD only) ftp.
966 --alt 42
969 Bypass Fetch as a downloader option. Priority is: Perl
970 (HTTP::Tiny), Curl, Wget, Fetch, (OpenBSD only) ftp.
971 --alt 43
974 Bypass Wget as a downloader option. Priority is: Perl
975 (HTTP::Tiny), Curl, Wget, Fetch, OpenBSD only: ftp
976 --alt 44
979 Bypass Curl, Fetch, and Wget as downloader options. This basi‐
980 cally forces the downloader selection to use Perl 5.x
981 HTTP::Tiny, which is generally slower than Curl or Wget but it
982 may help bypass issues with downloading.
983 --display [:<integer>]
986 Will try to get display data out of X (does not usually work as
987 root user). Default gets display info from display :0. If you
988 use the format --display :1 then it would get it from display 1
989 instead, or any display you specify.
990 Note that in some cases, --display will cause inxi to hang end‐
992 lessly when running the option in console with Intel graphics.
993 The situation regarding other free drivers such as nouveau/ATI
994 is currently unknown. It may be that this is a bug with the
995 Intel graphics driver - more information is required.
996 You can test this easily by running the following command out of
998 X/display server: glxinfo -display :0
999 If it hangs, --display will not work.
1001 --dmidecode
1004 Force use of dmidecode. This will override /sys data in some
1005 lines, e.g. -M or -B.
1006 --downloader [curl|fetch|perl|wget]
1009 Force inxi to use Curl, Fetch, Perl, or Wget for downloads.
1010 --host Turns on hostname in System line. Overrides inxi config file
1013 value (if set):
1014 SHOW_HOST='false'
1016 --indent-min [integer]
1019 Overrides default indent minimum value. This is the value that
1020 makes inxi change from wrapped line starters [like Info] to non
1021 wrapped. If less than 80, no wrapping will occur. Overrides
1022 internal default value and user configuration value:
1023 INDENT_MIN=85
1025 --limit [-1 - x]
1028 Raise or lower max output limit of IP addresses for -i. -1
1029 removes limit.
1030 --man Updates / installs man page with -U if pinxi or using -U 3 dev
1033 branch. (Only active if -U is is not disabled by maintainers).
1034 --no-host
1037 Turns off hostname in System line. Useful, in combination with
1038 -z, for anonymizing inxi output for posting on forums or IRC.
1039 Same as configuration value:
1040 SHOW_HOST='false'
1042 --no-man
1045 Disables man page install with -U for master and active develop‐
1046 ment branches. (Only active if -U is is not disabled by main‐
1047 tainers).
1048 --no-ssl
1051 Skip SSL certificate checks for all downloader actions (-U, -w,
1052 -W, -i). Use if your system does not have current SSL certifi‐
1053 cate lists, or if you have problems making a connection for any
1054 reason. Works with Wget, Curl, and Fetch only.
1055 --no-sudo
1058 Skips the use of sudo to run certain internal features (like
1059 hddtemp, file) with sudo. Not related to running inxi itself
1060 with sudo or super user. Some systems will register errors which
1061 will then trigger admin emails in such cases, so if you want to
1062 disable regular user use of sudo (which requires configuration
1063 to setup anyway for these options) just use this option, or
1064 NO_SUDO configuration item.
1065 --output [json|screen|xml]
1068 Change data output type. Requires --output-file if not screen.
1069 --output-file [full path to output file|print]
1072 The given directory path must exist. The directory path given
1073 must exist, The print options prints to stdout. Required for
1074 non-screen --output formats (json|xml).
1075 --partition-sort [dev-base|fs|id|label|percent-used|size|uuid|used]
1078 Change default sort order of partition output. Corresponds to
1079 PARTITION_SORT configuration item. These are the available sort
1080 options:
1081 dev-base - /dev partition identifier, like /dev/sda1. Note that
1083 it's an alphabetic sort, so sda12 is before sda2.
1084 fs - Partition filesystem. Note that sorts will be somewhat ran‐
1086 dom if all filesystems are the same.
1087 id - Mount point of partition (default).
1089 label - Label of partition. If partitions have no labels, sort
1091 will be random.
1092 percent-used - Percentage of partition size used.
1094 size - KiB size of partition.
1096 uuid - UUID of the partition.
1098 used - KiB used of partition.
1100 --pm-type [package manager name]
1103 For distro package maintainers only, and only for non apt, rpm,
1104 or pacman based systems. To be used to test replacement package
1105 lists for recommends for that package manager.
1106 --sleep [0-x.x]
1109 Usually in decimals. Change CPU sleep time for -C (current:
1110 .35). Sleep is used to let the system catch up and show a more
1111 accurate CPU use. Example:
1112 inxi -Cxxx --sleep 0.15
1114 Overrides default internal value and user configuration value:
1116 CPU_SLEEP=0.25
1118 --tty Forces internal IRC flag to off. Used in unhandled cases where
1121 the program running inxi may not be seen as a shell/tty, but it
1122 is not an IRC client. Put --tty first in option list to avoid
1123 unexpected errors. If you want a specific output width, use the
1124 --width option. If you want normal color codes in the output,
1125 use the -c [color ID] flag.
1126 The sign you need to use this is extra numbers before the
1128 key/value pairs of the output of your program. These are IRC,
1129 not TTY, color codes. Please post a github issue if you find you
1130 need to use --tty (including the full -Ixxx line) so we can fig‐
1131 ure out how to add your program to the list of whitelisted pro‐
1132 grams.
1133 You can see what inxi believed started it in the -Ixxx line,
1135 Shell: or Client: item. Please let us know what that result was
1136 so we can add it to the parent start program whitelist.
1137 --usb-sys
1140 Forces the USB data generator to use /sys as data source instead
1141 of lsusb.
1142 --usb-tool
1145 Forces the USB data generator to use lsusb as data source. Over‐
1146 rides USB_SYS in user configuration file(s).
1147 --wan-ip-url [URL]
1150 Force -i to use supplied URL as WAN IP source. Overrides dig or
1151 default IP source urls. URL must start with http[s] or ftp.
1152 The IP address from the URL must be the last item on the last
1154 (non-empty) line of the page content source code.
1155 Same as configuration value (example):
1157 WAN_IP_URL='https://mysite.com/ip.php'
1159 --wm Force System item wm to use wmctrl as data source, override
1162 default ps source.
1163
1166 --dbg 1
1167 - Debug downloader failures. Turns off silent/quiet mode for
1168 curl, wget, and fetch. Shows more downloader action information.
1169 Shows some more information for Perl downloader.
1170 --debug [1-3]
1173 - On screen debugger output. Output varies depending on current
1174 needs Usually nothing changes.
1175 --debug 10
1178 - Basic logging. Check $XDG_DATA_HOME/inxi/inxi.log or
1179 $HOME/.local/share/inxi/inxi.log or $HOME/.inxi/inxi.log.
1180 --debug 11
1183 - Full file/system info logging.
1184 --debug 20
1187 Creates a tar.gz file of system data and collects the inxi out‐
1188 put in a file.
1189 * tree traversal data file(s) read from /proc and /sys, and
1191 other system data.
1192 * xorg conf and log data, xrandr, xprop, xdpyinfo, glxinfo etc.
1194 * data from dev, disks, partitions, etc.
1196 --debug 21
1199 Automatically uploads debugger data tar.gz file to ftp.techpat‐
1200 terns.com, then removes the debug data directory, but leaves the
1201 debug tar.gz file. See --ftp for uploading to alternate loca‐
1202 tions.
1203 --debug 22
1206 Automatically uploads debugger data tar.gz file to ftp.techpat‐
1207 terns.com, then removes the debug data directory and the tar.gz
1208 file. See --ftp for uploading to alternate locations.
1209 --ftp [ftp.yoursite.com/incoming]
1212 For alternate ftp upload locations: Example:
1213 inxi --ftp ftp.yourserver.com/incoming --debug 21
1215
1218 Only used the following in conjunction with --debug 2[012], and only
1219 use if you experienced a failure or hang, or were instructed to do so.
1220 --debug-proc
1223 Force debugger to parse /proc directory data when run as root.
1224 Normally this is disabled due to unpredictable data in /proc
1225 tree.
1226 --debug-proc-print
1229 Use this to locate file that /proc debugger hangs on.
1230 --debug-no-exit
1233 Skip exit on error when running debugger.
1234 --debug-no-proc
1237 Skip /proc debugging in case of a hang.
1238 --debug-no-sys
1241 Skip /sys debugging in case of a hang.
1242 --debug-sys
1245 Force PowerPC debugger parsing of /sys as sudo/root.
1246 --debug-sys-print
1249 Use this to locate file that /sys debugger hangs on.
1250
1253 BitchX, Gaim/Pidgin, ircII, Irssi, Konversation, Kopete, KSirc, KVIrc,
1254 Weechat, and Xchat. Plus any others that are capable of displaying
1255 either built-in or external script output.
1256
1259 To trigger inxi output in your IRC client, pick the appropriate method
1260 from the list below:
1261 Hexchat, XChat, Irssi
1263 (and many other IRC clients) /exec -o inxi [options] If you
1264 don't include the -o, only you will see the output on your local
1265 IRC client.
1266 Konversation
1268 /cmd inxi [options]
1269 To run inxi in Konversation as a native script if your distribu‐
1271 tion or inxi package hasn't already done this for you, create
1272 this symbolic link:
1273 KDE 4: ln -s /usr/local/bin/inxi /usr/share/kde4/apps/konversa‐
1275 tion/scripts/inxi
1276 KDE 5: ln -s /usr/local/bin/inxi /usr/share/konversa‐
1278 tion/scripts/inxi
1279 If inxi is somewhere else, change the path /usr/local/bin to
1281 wherever it is located.
1282 If you are using KDE/QT 5, then you may also need to add the
1284 following to get the Konversation /inxi command to work:
1285 ln -s /usr/share/konversation /usr/share/apps/
1287 Then you can start inxi directly, like this:
1289 /inxi [options]
1291 WeeChat
1293 NEW: /exec -o inxi [options]
1294 OLD: /shell -o inxi [options]
1296 Newer (2014 and later) WeeChats work pretty much the same now as
1298 other console IRC clients, with /exec -o inxi [options]. Newer
1299 WeeChats have dropped the -curses part of their program name,
1300 i.e.: weechat instead of weechat-curses.
1301
1304 inxi will read its configuration/initialization files in the following
1305 order:
1306 /etc/inxi.conf contains the default configurations. These can be over‐
1308 ridden by user configurations found in one of the following locations
1309 (inxi will store its config file using the following precedence: if
1310 $XDG_CONFIG_HOME is not empty, it will go there, else if
1311 $HOME/.conf/inxi.conf exists, it will go there, and as a last default,
1312 the legacy location is used), i.e.:
1313 $XDG_CONFIG_HOME/inxi.conf > $HOME/.conf/inxi.conf >
1315 $HOME/.inxi/inxi.conf
1316
1319 See the documentation page for more complete information on how to set
1320 these up, and for a complete list of options:
1321 https://smxi.org/docs/inxi-configuration.htm
1323 Basic Options
1325 Here's a brief overview of the basic options you are likely to
1326 want to use:
1327 COLS_MAX_CONSOLE The max display column width on terminal.
1329 COLS_MAX_IRC The max display column width on IRC clients.
1331 COLS_MAX_NO_DISPLAY The max display column width in console, out
1333 of GUI desktop.
1334 CPU_SLEEP Decimal value 0 or more. Default is usually around
1336 0.35 seconds. Time that inxi will 'sleep' before getting CPU
1337 speed data, so that it reflects actual system state.
1338 DOWNLOADER Sets default inxi downloader: curl, fetch, ftp, perl,
1340 wget. See --recommends output for more information on download‐
1341 ers and Perl downloaders.
1342 FILTER_STRING Default <filter>. Any string you prefer to see
1344 instead for filtered values.
1345 INDENT_MIN The point where the line starter wrapping to its own
1347 line happens. Overrides default. See --indent-min. If 80 or
1348 less, wrap will never happen.
1349 LIMIT Overrides default of 10 IP addresses per IF. This is only
1351 of interest to sys admins running servers with many IP
1352 addresses.
1353 NO_SUDO Set to 1 or true to disable internal use of sudo.
1355 PARTITION_SORT Overrides default partition output sort. See
1357 --partition-sort for options.
1358 PS_COUNT The default number of items showing per -t type, m or
1360 c. Default is 5.
1361 SENSORS_CPU_NO In cases of ambiguous temp1/temp2 (inxi can't
1363 figure out which is the CPU), forces sensors to use either
1364 value 1 or 2 as CPU temperature. See the above configuration
1365 page on smxi.org for full info.
1366 SEP2_CONSOLE Replaces default key / value separator of ':'.
1368 USB_SYS Forces all USB data to use /sys instead of lsusb.
1370 WAN_IP_URL Forces -i to use supplied URL, and to not use dig
1372 (dig is generally much faster). URL must begin with http or ftp.
1373 Note that if you use this, the downloader set tests will run
1374 each time you start inxi whether a downloader feature is going
1375 to be used or not.
1376 The IP address from the URL must be the last item on the last
1378 (non-empty) line of the URL's page content source code.
1379 Same as --wan-ip-url [URL]
1381 WEATHER_SOURCE Values: [0-9]. Same as --weather-source. Values
1383 4-9 are not currently supported, but this can change at any
1384 time.
1385 WEATHER_UNIT Values: [c|f|cf|fc]. Same as --weather-unit.
1387 Color Options
1390 It's best to use the -c [94-99] color selector tool to set the
1391 following values because it will correctly update the configura‐
1392 tion file and remove any invalid or conflicting items, but if
1393 you prefer to create your own configuration files, here are the
1394 options. All take the integer value from the options available
1395 in -c 94-99.
1396 NOTE: All default and configuration file set color values are
1398 removed when output is piped or redirected. You must use the
1399 explicit -c <color number> option if you want colors to be
1400 present in the piped/redirected output (creating a PDF for exam‐
1401 ple).
1402 CONSOLE_COLOR_SCHEME The color scheme for console output (not in
1404 X/Wayland).
1405 GLOBAL_COLOR_SCHEME Overrides all other color schemes.
1407 IRC_COLOR_SCHEME Desktop X/Wayland IRC CLI color scheme.
1409 IRC_CONS_COLOR_SCHEME Out of X/Wayland, IRC CLI color scheme.
1411 IRC_X_TERM_COLOR_SCHEME In X/Wayland IRC client terminal color
1413 scheme.
1414 VIRT_TERM_COLOR_SCHEME Color scheme for virtual terminal output
1416 (in X/Wayland).
1417
1420 Please report bugs using the following resources.
1421 You may be asked to run the inxi debugger tool (see --debug 21/22),
1423 which will upload a data dump of system files for use in debugging
1424 inxi. These data dumps are very important since they provide us with
1425 all the real system data inxi uses to parse out its report.
1426 Issue Report
1428 File an issue report: https://github.com/smxi/inxi/issues
1429 Developer Forums
1431 Post on inxi developer forums: https://techpat‐
1432 terns.com/forums/forum-32.html
1433 IRC irc.oftc.net#smxi
1435 You can also visit irc.oftc.net channel: #smxi to post issues.
1436
1439 https://github.com/smxi/inxi
1440 https://smxi.org/docs/inxi.htm
1442
1445 inxi is a fork of locsmif's very clever infobash script.
1446 Original infobash author and copyright holder: Copyright (C) 2005-2007
1448 Michiel de Boer aka locsmif
1449 inxi version: Copyright (C) 2008-18 Harald Hope
1451 This man page was originally created by Gordon Spencer (aka aus9) and
1453 is maintained by Harald Hope (aka h2 or TechAdmin).
1454 Initial CPU logic, konversation version logic, occasional maintenance
1456 fixes, and the initial xiin.py tool for /sys parsing (obsolete, but
1457 still very much appreciated for all the valuable debugger data it
1458 helped generate): Scott Rogers
1459 Further fixes (listed as known):
1461 Horst Tritremmel <hjt at sidux.com>
1463 Steven Barrett (aka: damentz) - USB audio patch; swap percent used
1465 patch.
1466 Jarett.Stevens - dmidecode -M patch for older systems with no /sys.
1468
1471 The nice people at irc.oftc.net channels #linux-smokers-club and #smxi,
1472 who all really have to be considered to be co-developers because of
1473 their non-stop enthusiasm and willingness to provide real-time testing
1474 and debugging of inxi development.
1475 Siduction forum members, who have helped get some features working by
1477 providing a large number of datasets that have revealed possible varia‐
1478 tions, particularly for the RAM -m option.
1479 AntiX users and admins, who have helped greatly with testing and debug‐
1481 ging, particularly for the 3.0.0 release.
1482 ArcherSeven (Max), Brett Bohnenkamper (aka KittyKatt), and Iotaka, who
1484 always manage to find the weirdest or most extreme hardware and setups
1485 that help make inxi much more robust.
1486 For the vastly underrated skill of output error/glitch catching, Pete
1488 Haddow. His patience and focus in going through inxi repeatedly to find
1489 errors and inconsistencies is much appreciated.
1490 All the inxi package maintainers, distro support people, forum modera‐
1492 tors, and in particular, sys admins with their particular issues, which
1493 almost always help make inxi better, and any others who contribute
1494 ideas, suggestions, and patches.
1495 Without a wide range of diverse Linux kernel-based Free Desktop systems
1497 to test on, we could never have gotten inxi to be as reliable and solid
1498 as it's turning out to be.
1499 And of course, a big thanks to locsmif, who figured out a lot of the
1501 core methods, logic, and tricks originally used in inxi Gawk/Bash.
1502inxi 2019-11-19 INXI(1)