1AMANDA-INTERACTIVIT(7) Miscellanea AMANDA-INTERACTIVIT(7)
2
3
4
6 amanda-interactivity - Configuring Interactivity with Amanda Amanda
7
9 Amanda uses interactivity to ask user to load specific volumes when
10 they are needed. This manual page describes the interactivity modules
11 included with Amanda.
12
13 This is a user-level description of the API, and does not address
14 details that are only of concern to developers of new interactivity
15 plugins. For that purpose, consult the Amanda source code, perldoc
16 'Amanda::Interactivity' and http://wiki.zmanda.com.
17
19 Interactivity is specified in amanda.conf(5) as follows:
20
21 define interactivity $interactivity_name {
22 comment "$comment"
23 plugin "$pluginname"
24 property "$PROPERTY_NAME" "$PROPERTY_VALUE"
25 ...
26 }
27 and then referenced in the global section as
28
29 interactivity "$interactivity_name"
30
31 Interactivity properties, like Amanda configuration parameters, are
32 insensitive to case, and - (dash) and _ (underscore) may be used
33 interchangeably.
34
35 See the individual plugin sections, below for properties applicable to
36 each plugin.
37
39 Amanda provides three interactivity modules, tty, email and tty_email.
40
41 TTY
42 The tty interactivity module uses the tty to communicate with the user,
43 it works only if a terminal is available, which is the case if amanda
44 is executed from a command line.
45
46 When promted for a volume, the user must put the requested volume in
47 the changer and type <enter>. User can type the name of another changer
48 if the volume is available in that changer. Typing 'abort' will abort
49 the operation.
50
51 EMAIL
52 The email interactivity module uses email to send requests to the user,
53 and reads replies from the filesystem.
54
55 The email module has many properties:
56
57 check-file
58
59 If set, amanda will check this file for user input. The user can
60 touch the file to tell amanda that the requested volume was
61 inserted in the changer. If the user writes the name of a changer
62 into the file, Amanda will use that changer. If the user writes
63 the word 'abort' into the file, the scan will be aborted.
64
65 check-file-delay
66
67 Default: 10. This integer property indicates the time in seconds
68 between each check of the check-file.
69
70 mailto
71
72 Default: global value of mailto. The email addresses to which the
73 email should be sent. If multiple addresses are given, they should
74 be separated by spaces.
75
76 resend-delay
77
78 Default 0. The time in seconds between emails. Amanda will resend
79 the same email at this frequency, which can be useful if mailto is
80 a pager or phone. If set to 0, only one email is sent.
81
82 TTY_EMAIL
83 The tty_email interactivity module uses the tty module if a terminal is
84 available and uses the email module otherwise. Its properties are a
85 combination of properties from each module.
86
88 define interactivity "by-tty-or-email" {
89 comment "Send email on runs from cron; use terminal on command line"
90 plugin "tty_email"
91 property "mailto" "admin1" "admin2" "me@home"
92 property "resend-delay" "1800" #every 30 minutes
93 property "check-file" "/tmp/email_input"
94 property "check-file-delay" "10" #every 10 seconds
95 }
96
98 amanda(8), amanda.conf(5)
99
100 The Amanda Wiki: : http://wiki.zmanda.com/
101
103 Jean-Louis Martineau <martineau@zmanda.com>
104 Zmanda, Inc. (http://www.zmanda.com)
105
106
107
108Amanda 3.5.1 12/01/2017 AMANDA-INTERACTIVIT(7)