uisp(1) - f36

1UISP(1)                          User Commands                         UISP(1)
2
3
4

NAME

6       uisp - manual page for uisp
7

SYNOPSIS

9       uisp  [OPTION]..  -dprog=TYPE  -dpart=AT90XXX  --FUNCTION.. [if=SOURCE]
10       [of=DEST]
11

DESCRIPTION

13   Programming Methods:
14       -dprog=avr910|pavr|stk500
15
16              avr910 Standard Atmel Serial Programmer/Atmel Low Cost  Program‐
17                     mer
18
19              pavr   http://www.avr1.org/pavr/pavr.html
20
21              stk500 Atmel STK500
22
23       -dprog=dapa|stk200|abb|atdh|avrisp|bsd|fbprg|dt006|maxi|dm04|dasa|dasa2|dasa3
24
25              dapa   Direct AVR Parallel Access
26
27              stk200 Parallel Starter Kit STK200, STK300
28
29              abb    Altera ByteBlasterMV Parallel Port Download Cable
30
31              atdh   Atmel-ISP Download Cable (P/N ATDH1150VPC)
32
33              avrisp Atmel AVR ISP (?)
34
35              bsd    http://www.bsdhome.com/avrdude/ (parallel)
36
37              fbprg  http://ln.com.ua/~real/avreal/adapters.html (parallel)
38
39              dt006  http://www.dontronics.com/dt006.html (parallel)
40
41              maxi   Investment Technologies Maxi (parallel)
42
43              dm04   Datamekatronik 2004 (parallel)
44
45              dasa   serial (RESET=RTS SCK=DTR MOSI=TXD MISO=CTS)
46
47              dasa2  serial (RESET=!TXD SCK=RTS MOSI=DTR MISO=CTS)
48
49              dasa3  serial (RESET=!DTR SCK=RTS MOSI=TXD MISO=CTS)
50
51   Target Device Selection:
52       -dpart=part
53              Set target abbreviated name or number. For some programmers,  if
54              -dpart  is  not given programmer's supported devices are listed.
55              Set -dpart=auto for auto-select. Auto-select does not work  with
56              all programmers, so it is recommended to always specify a target
57              device explicitly.
58
59   Parallel Device Settings:
60       -dlpt=address|device name
61              specify device name (Linux ppdev, FreeBSD ppi, serial) or direct
62              I/O parallel port address (0x378, 0x278, 0x3BC)
63
64       -dno-poll
65              Program without data polling (a little slower)
66
67       -dno-retry
68              Disable retries of program enable command
69
70       -dvoltage=value
71              Set  timing  specs  according to the power supply voltage in [V]
72              (default 3.0)
73
74       -dt_sck=time
75              Set minimum SCK high/low time in micro-seconds (default 5)
76
77       -dt_wd_flash=time
78              Set FLASH maximum write delay time in micro-seconds
79
80       -dt_wd_eeprom=time
81              Set EEPROM maximum write delay time in micro-seconds
82
83       -dt_reset=time
84              Set reset inactive (high) time in micro-seconds
85
86       -dinvert=[sck[,mosi[,miso[,reset]]]]]
87              Invert specified lines Use -v=3 option to see current settings.
88
89       -d89   Allow parallel programming of AT89S51 and AT89S52 devices.
90
91   Atmel Low Cost Programmer Serial Device Settings:
92       -dserial=device name
93              Set serial interface as /dev/ttyS* (default /dev/avr)
94
95       -dspeed=1200|2400|4800|9600|19200|38400|57600|115200
96              Set speed of the serial interface (default 19200)
97
98   Stk500 specific options:
99       -dhiv  Use Hi-V programming instead of SPI (default is SPI).
100
101       --rd_aref
102              Read the ARef Voltage. Note that due to  a  bug  in  the  stk500
103              firmware, the read value is sometimes off by 0.1 from the actual
104              value measured with a volt meter.
105
106       --wr_aref=value
107              Set the ARef Voltage. Valid values are 0.0 to 6.0 volts  in  0.1
108              volt  increments.   Value  can  not  be  larger than the VTarget
109              value.
110
111       --rd_vtg
112              Read the Vtarget Voltage. Note that due to a bug in  the  stk500
113              firmware, the read value is sometimes off by 0.1 from the actual
114              value measured with a volt meter.
115
116       --wr_vtg=value
117              Set the VTarget Voltage. Valid values are 0.0 to  6.0  volts  in
118              0.1  volt  increments.   Value  can not be smaller than the ARef
119              value.
120
121       --rd_osc
122              Read the oscillator frequency in Hertz.
123
124       --wr_osc=value
125              Set the oscillator frequency in Hertz, from 14.06 to 3686400.
126
127   Functions:
128       --upload
129              Upload "input_file" to the AVR memory.
130
131       --verify
132              Verify "input_file" (processed after the --upload opt.)
133
134       --download
135              Download AVR memory to "output_file" or stdout.
136
137       --erase
138              Erase device.
139
140       --segment=flash|eeprom|fuse
141              Set active segment (auto-select for AVA Motorola output)
142
143   Fuse/Lock Bit Operations:
144       --rd_fuses
145              Read all fuses and print values to stdout
146
147       --wr_fuse_l=byte
148              Write fuse low byte
149
150       --wr_fuse_h=byte
151              Write fuse high byte
152
153       --wr_fuse_e=byte
154              Write fuse extended byte
155
156       --wr_lock=byte
157              Write lock bits. Argument is a byte where each bit is:
158               Bit5 -> blb12
159               Bit4 -> blb11
160               Bit3 -> blb02
161               Bit2 -> blb01
162               Bit1 -> lb2
163               Bit0 -> lb1
164
165       --lock Write lock bits [old method; deprecated].
166
167   Files:
168       if=filename
169              Input file for the --upload and --verify functions  in  Motorola
170              S-records (S1 or S2) or 16 bit Intel format
171
172       of=filename
173              Output  file  for  the --download function in Motorola S-records
174              format, default is standard output
175
176   Other Options:
177       -v=level
178              Set verbose level (-v equals -v=2, min/max: 0/4, default 1)
179
180       --hash=perbytes
181              Print hash (default is 32 bytes)
182
183       --help -h
184              Help
185
186       --version
187              Print version information
188
189       --terminal
190              Invoke shell-like terminal
191

AUTHOR

193       Written by Uros Platise.
194

REPORTING BUGS

196       Report bugs to <uisp-dev@nongnu.org>
197

COPYRIGHT

202       (c) 1997-1999 Uros Platise, 2000-2004 Marek Michalkiewicz
203
204       uisp is free software, covered by the GNU General Public License.   You
205       are  welcome to change it and/or distribute copies of it under the con‐
206       ditions of the GNU General Public License.
207
208
209
210uisp version 20050207            January, 2022                         UISP(1)

NAME

SYNOPSIS

DESCRIPTION

AUTHOR

REPORTING BUGS

SEE ALSO

COPYRIGHT