freeipmi(7)

1FREEIPMI(7)                        Overview                        FREEIPMI(7)
2
3
4

NAME

6       FreeIPMI - FreeIPMI overview
7

Introduction

9       FreeIPMI  provides  in-band  and out-of-band IPMI software based on the
10       IPMI v1.5/2.0 specification.
11

What is IPMI?

13       The IPMI specification defines a set of interfaces for platform manage‐
14       ment  and is implemented by a number vendors for system management. The
15       features of IPMI that most users will be interested in are sensor moni‐
16       toring,  system  event  monitoring,  power control, and serial-over-LAN
17       (SOL). The FreeIPMI tools and libraries  listed  below  should  provide
18       users  with the ability to access and utilize these and many other fea‐
19       tures of IPMI.
20

Getting Started with IPMI

22       IPMI can be used in-band (i.e. running on a machine locally) or out-of-
23       band (i.e. connecting remotely).
24
25       Most  FreeIPMI  tools  can  operate in-band by using one of the in-band
26       drivers included. These in-band drivers include a userspace KCS  inter‐
27       face  driver,  a  SSIF  driver  through  the  Linux  SSIF  device (i.e.
28       /dev/i2c-0), the OpenIPMI Linux kernel driver  (i.e.  /dev/ipmi0),  the
29       Sun/Solaris  BMC  driver (i.e. /dev/bmc), and the Intel DCMI/MEI driver
30       (i.e. /dev/dcmi). If your system requires the use of installed drivers,
31       those  appropriate  modules  must be installed ahead of time.  However,
32       most systems should automatically load these drivers when appropriate.
33
34       Under most scenarios, the FreeIPMI tools should automatically  discover
35       which  in-band  interface  to use and the proper settings to use. Users
36       may execute the tools on the command line to  begin  using  them.  Some
37       motherboards  may  require  you  to  determine  driver type, addresses,
38       paths, etc. on your own and pass them as command line  options  to  the
39       tools.  You  may use ipmi-locate(8) to help determine this information.
40       Other tools such as dmidecode(8) may also provide this information.
41
42       To use IPMI out-of-band with tools such as  ipmipower(8)  or  ipmi-sen‐
43       sors(8),  the  remote machine's BMC must first be configured for out of
44       band communication. Typically, this involves setting a username,  pass‐
45       word,  IP address, MAC address, and a few other parameters. This can be
46       done using the tool ipmi-config(8).  Additional information on  how  to
47       configure  with  ipmi-config(8) can be found in the ipmi-config.conf(5)
48       manpage. Some vendors may pre-configure their motherboards with default
49       values so that ipmi-config(8) can be used remotely to configure the ma‐
50       chine. However, most of the time, the BMC must  be  configured  in-band
51       before  out-of-band  access can be allowed (for example, the correct IP
52       address and MAC address must be configured).
53
54       In order to remotely connect to a machine, you typically  must  specify
55       the host, username, and password for the tool in order to connect.  De‐
56       pending on configuration settings, a K_g key, privilege level,  authen‐
57       tication  type,  cipher  suite  id,  or protocol version may need to be
58       specified.
59
60       Some vendors may have not implemented IPMI properly  and  a  workaround
61       must  be  specified  into FreeIPMI to ensure the tool can execute prop‐
62       erly. For example, a fair number of vendors have  populated  their  FRU
63       records  with invalid checksums. To properly ignore these set of check‐
64       sums a skipchecks workaround has been added to ipmi-fru(8).  Please see
65       each of the tool manpages to see a list of available workarounds.
66
67       Additional  information,  examples, and general trouble-shooting can be
68       found in each of the tool manpages.
69

General Use

71       The primary tools that most users of FreeIPMI will be interested in for
72       system management are the following:
73
74       ipmi-sensors
75
76       A tool to read IPMI sensor readings to aid in system monitoring.
77
78       ipmi-sel
79
80       A tool to read and manage IPMI System Event Log (SEL) records to aid in
81       system debugging.
82
83       ipmipower
84
85       A tool for remote power control.
86
87       ipmiconsole
88
89       A tool for Serial-over-Lan (SOL) console access.
90
91       Many other tools and libraries are listed below that  cover  additional
92       features and areas of IPMI.
93
94       Additional  information,  examples, and general trouble-shooting can be
95       found in each of the tool manpages.
96

Configuration

98       In order to avoid typing in a long list  of  command  line  options  to
99       specify  IPMI  communication  requirements every time a command is exe‐
100       cuted (e.g. driver paths, usernames, passwords, etc.), an alternate set
101       of  default  values  can be set for most FreeIPMI tools in the FreeIPMI
102       configuration file. See freeipmi.conf(5) for more information.
103

HPC Support

105       Much of FreeIPMI was written with HPC support in mind.   Ipmi-config(8)
106       comes  with  file  input/output  support  so  that configuration can be
107       copied and verified across nodes in a cluster.  Most  tools  (like  ip‐
108       mipower(8)  and ipmi-sensors(8) ) come with hostrange support so multi‐
109       ple hosts can be specified on the command line at  the  same  time  and
110       IPMI  can  be executed against the hosts in parallel. See tool manpages
111       for more information.  Also see the document freeipmi-hostrange.txt for
112       detailed  usage  and explanation.  Ipmi-sensors(8) and the libipmimoni‐
113       toring(3) library support the ability to interpret sensor  readings  as
114       well  as  just reporting them. By mapping sensor readings into NOMINAL,
115       WARNING, or CRITICAL states, it makes monitoring sensors easier  across
116       large numbers of nodes.
117

Development

119       For  information  on the libraries that can be used to program IPMI ap‐
120       plications with, please see libfreeipmi(3), libipmiconsole(3), libipmi‐
121       monitoring(3),  and libipmidetect(3).  Or see the document freeipmi-li‐
122       braries.txt.
123

Project Tools

125       The following tools are distributed and supported by FreeIPMI.
126
127       bmc-info
128
129       A tool to read information about a BMC such as device version  numbers,
130       device support, and globally unique IDs (guids).
131
132       bmc-watchdog
133
134       A tool/daemon to manage a BMC Watchdog. This tool is typically used for
135       system timeout management and automatic system restarts in the event of
136       a system crash.
137
138       ipmi-chassis
139
140       A  tool to manage/monitor a chassis, such as chassis power, identifica‐
141       tion (i.e. LED control), and status.
142
143       ipmi-fru
144
145       A tool to read field replaceable unit (FRU) information from a  mother‐
146       board/machine.
147
148       ipmi-sel
149
150       A  tool  to  read  and  manage IPMI System Event Log (SEL) records. SEL
151       records store system event information and may be useful for  debugging
152       problems.
153
154       ipmi-sensors
155
156       A  tool  to  read IPMI sensor readings and sensor data repository (SDR)
157       information.
158
159       ipmipower
160
161       A tool for remote power control.
162
163       ipmiconsole
164
165       A tool for Serial-over-Lan (SOL) console access.
166
167       ipmi-config
168
169       A tool to configure BMC and IPMI information. In can be used to config‐
170       ured  usernames,  passwords,  networking information, security, Serial-
171       over-LAN (SOL), Platform Event Filtering  (PEF),  boot  devices,  power
172       restoration  policy,  sensor  thresholds,  sensor events, and many more
173       configuration options.
174
175       ipmi-raw
176
177       A tool that provides hex input/output of IPMI commands.
178
179       ipmi-locate
180
181       A tool that can probe for information about the location of a  BMC  de‐
182       vice, such as device addresses.
183
184       ipmi-pet
185
186       A tool to parse and interpret Platform Event Traps (PET).
187
188       ipmi-dcmi
189
190       A  tool  to perform Data Center Manageability Interface (DCMI) IPMI ex‐
191       tension commands. Supports extensions for asset  management  and  power
192       usage management.
193
194       bmc-device
195
196       A  tool  to  perform  advanced BMC commands, such as resetting the BMC,
197       configuring ACPI, configuring SDR/SEL time, manually generating events,
198       re-arming sensors, and configuring manufacturer settings.
199
200       ipmiping
201
202       An IPMI ping tool for debugging.
203
204       rmcpping
205
206       A RMCP ping tool for debugging.
207
208       ipmi-oem
209
210       An IPMI tool for OEM specific commands.
211
212       ipmidetect/ipmidetectd
213
214       A tool and daemon for IPMI node detection.
215
216       ipmiseld
217
218       A  daemon that regularly polls the SEL and stores the events to the lo‐
219       cal syslog.
220
221       Additional information, examples, and general trouble-shooting  can  be
222       found in each of the tool manpages.
223

Project Libraries

225       The following libraries are distributed and supported by FreeIPMI.
226
227       libfreeipmi
228
229       A  C  library  that includes KCS, SSIF, and OpenIPMI Linux, and Solaris
230       BMC drivers, IPMI 1.5 and IPMI 2.0 LAN communication  interfaces,  IPMI
231       packet  building  utilities,  IPMI command utilities, and utilities for
232       reading/interpreting/managing IPMI. This library is for programmers in‐
233       timately  familiar with the IPMI protocol and IPMI specification.  Most
234       users may wish to use the libraries listed below.
235
236       libipmiconsole
237
238       A library for Serial-over-Lan (SOL) console access. SOL console  access
239       is  abstracted  into a file descriptor interface, so users may read and
240       write console data through a file descriptor.
241
242       libipmimonitoring
243
244       A library for sensor and system event log  (SEL)  monitoring  that  ab‐
245       stracts  away  most  IPMI  details. Interpretation of those sensors and
246       events is abstracted into an API with an iterator interface.
247
248       libipmidetect
249
250       A library for IPMI node detection.
251

REPORTING BUGS

253       Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
254

COPYRIGHT

256       Copyright © 2003-2015 FreeIPMI Core Team.
257
258       FreeIPMI is free software; you can redistribute it and/or modify it un‐
259       der  the  terms  of  the GNU General Public License as published by the
260       Free Software Foundation; either version 3 of the License, or (at  your
261       option) any later version.
262