1PPSCHECK(8)                   GPSD Documentation                   PPSCHECK(8)
2
3
4

NAME

6       ppscheck - tool to check a serial port for PPS
7

SYNOPSIS

9       ppscheck [-?] [--help] [-p] [--pps] [--version] [-h] [-V]
10
11       ppscheck [-m] device
12

DESCRIPTION

14       ppscheck watches a specified serial port for transitions that might be
15       PPS. It looks for changes in handshake lines CD, CTS, DSR, and RI by
16       running ioctl(...., TIOCMIWAIT, ...) in a loop. When it sees a state
17       change it emits a timestamped line of output dumping the state of the
18       handshake signals. It’s useful for checking whether a device is
19       emitting PPS.
20
21       ppscheck can run as a normal user, but that user must have permissions
22       to read the target device. Running under sudo may, or may not, work.
23       Running as root will always work.
24
25       To check the first serial port do this:
26
27           # ppscheck /dev/ttyS0
28
29       As a side effect, ppscheck will try to create the matching /dev/ppsX by
30       setting the tty line discipline (ldisc) to N_PPS (18). You should then
31       have a device /dev/pps0. Note that not all serial devices support ldisc
32       N_PPS.
33
34       You can now use ppscheck to see if the KPPS (RFC 2783) interface is
35       working:
36
37           # ppscheck /dev/pps0
38
39       ppscheck is not intended for routine use, but rather for diagnostic
40       purposes. Once you have verified a particular device can output PPS
41       signals you will never need to use it again on that device.
42

OPTIONS

44       The program accepts the following options:
45
46       -?+, `+-h+, `+--help
47           Print help message, then exit.
48
49       -m+, `+--match
50           Find PPS device that matches device.
51
52       -p+, `+--pps
53           Print active PPS devices, then exit.
54
55       -V+, `+--version
56           Dump version, then exit.
57
58       -x SEC, --seconds SEC
59           Exit after delay of SEC seconds.
60

ARGUMENTS

62       The device argument should be the pathname of a device. Such as
63       /dev/ttyS0 or /dev/pps0. It will be the device monitored.
64
65       For a tty device, each output line is the second and nanosecond parts
66       of a timestamp followed by the names of the handshake signals then
67       asserted. Off transitions may generate lines with no signals asserted.
68
69       For a pps device, each output line will contain the assert and clear
70       times last detected by KPPS.
71
72       If you don’t see output within a second, use cgps, xgps, or some other
73       equivalent tool to check that your device has a satellite lock and is
74       getting 3D fixes before giving up on the possibility of PPS.
75
76       Check your cable. Cheap DB9 to DB9 cables such as those issued with
77       UPSes often carry TXD/RXD/GND only, omitting handshake lines such as
78       CD. Suspect this especially if the cable jacket looks too skinny to
79       hold more than three leads!
80
81       Most GPS that have built in USB do not support PPS. When in doubt,
82       contact the vendor for confirmation that your device does supply PPS.
83

RETURN VALUES

85       0
86           OK
87
88       1
89           if the device counld not be opened, or some other failure
90

SEE ALSO

92       cgps(1), xgps(1), gpsd(8)
93

RESOURCES

95       Project web site: https://gpsd.io/
96

COPYING

98       This file is Copyright 2013 by the GPSD project
99       SPDX-License-Identifier: BSD-2-clause
100

AUTHOR

102       Eric S. Raymond
103
104
105
106GPSD, Version 3.24                2022-04-27                       PPSCHECK(8)