1fcinfo(1M) System Administration Commands fcinfo(1M)
2
6 fcinfo, fcadm - Fibre Channel HBA Port Command Line Interface
7
9 fcinfo hba-port [-lite] [HBA_port_WWN]...
10 fcadm hba-port [-lite] [HBA_port_WWN]...
13 fcinfo remote-port [-ls] [-p HBA_port_WWN]
16 [REMOTE_port_WWN]...
17 fcadm remote-port [-ls] [-p HBA_port_WWN]
20 [REMOTE_port_WWN]...
21 fcinfo logical-unit | lu [-v] [OS device_path]
24 fcadm logical-unit | lu [-v] [OS device_path]
27 fcadm create-npiv-port -p Virtual_Port_WWN [-n Virtual_Node_WWN]
30 PhysicalPort_port_WWN
31 fcadm delete-npiv-port -p Virtual_Port_WWN [-n Virtual_Node_WWN]
34 PhysicalPort_port_WWN
35 fcadm create-fcoe-port [-tf] -p Port_WWN [-n Node_WWN]
38 MAC_Interface
39 fcadm delete-fcoe-port MAC_Interface
42 fcadm list-fcoe-ports MAC_Interface
45 fcadm force-lip Port_WWN
48 fcinfo [-V]
51 fcadm [-V]
54 fcinfo [-?]
57 fcadm [-?]
60
63 fcinfo and fcadm are command line interfaces that collect administra‐
64 tive information on fibre channel host bus adapter (HBA) ports on a
65 host. They also collect data on any fibre channel targets that might be
66 connected to those ports in a Storage Area Network (SAN).
67 A port can be either in initiator mode or target mode. The same FC
70 attribute information and remote port information are applied to both
71 the initiator and the target modes port except that SCSI-related opera‐
72 tions described below do not apply for the target mode port.
73 SUBCOMMANDS
75 The following subcommands are supported by both fcinfo and fcadm:
76 hba-port Lists information for the HBA port referenced by
78 the specified HBA_port_WWN. If HBA_port_WWN is not
79 specified, all initiator mode and target mode
80 fibre channel HBA ports on the host will be
81 listed.
82 remote-port Lists the remote-port information for those remote
85 ports that are specified. If no REMOTE_port_WWN is
86 specified, all remote ports that are visible
87 through HBA_port_WWN are listed.
88 logical-unit | lu Lists the logical unit referenced by the specified
91 device_path. If device_path is not specified, all
92 fibre channel logical units will be listed. This
93 subcommand applies only to the initiator mode.
94 The following subcommands, which administer N_Port ID Virtualization
98 (NPIV) HBA ports, are supported only by fcadm:
99 create-npiv-port
101 Create an NPIV virtual port on the specified adapter.
103 delete-npiv-port
106 Delete an NPIV virtual port. This delete only ports create by
108 fcadm.
109 The following subcommands, which administer Fibre Channel over Ethernet
113 (FCoE) ports, are supported only by fcadm:
114 create-fcoe-port
116 Creates a FCoE port associated with the given MAC interface and the
118 given Port_WWN/Node_WWN. If -p or -n is not specified, the Port WWN
119 or Node WWN will be generated automatically. If the specified MAC
120 interface does not support multiple unicast address, no FCoE port
121 will be created and you receive a message indicating that you can
122 add an -f option to force enabling promiscuous mode on the speci‐
123 fied MAC interface to enable FCoE.
124 delete-fcoe-port
127 Deletes the FCoE port associated with the specified MAC interface.
129 list-fcoe-ports
132 List information of FCoE ports.
134 force-lip
137 Force the link to reinitialize. When issuing this subcommand on
139 the target port side, causes a reset of the target port. When issu‐
140 ing it from the host port side, resets the host port. When an FC
141 switch is connected, other FC ports in the SAN will get a RSCN
142 (Remote State Change Notification). Furthermore, other initiators
143 will always rediscover the port after this, and the FC login ses‐
144 sion will be established or reused. Also, I/Os will be continued.
145 This command is disruptive to I/Os, but it is not destructive, as
146 it does not cause any data loss.
147
150 The following options are supported:
151 -e, --fcoe
153 Lists the information for all FCoE ports.
155 -f, --fcoe-promiscuous
158 Used with create-fcoe-port to create an FCoE port on a MAC inter‐
160 face associated with a NIC that does not support multiple unicast
161 address. Promiscuous mode will be enabled for the specified MAC
162 interface.
163 -l, --linkstat
166 Lists the link error statistics information for the port referenced
168 by the specified HBA_port_WWN or REMOTE_port_WWN.
169 -n HBA_node_WWN, --node HBA_node_WWN
172 When used with NPIV options, specify a virtual node WWN. If used
174 with create-npiv-port, it can be omitted, and a random based WWN
175 will be used. It is mandatory for delete-npiv-port.
176 When used with create-fcoe-port subcommand, specify the node WWN
178 for the FCoE port. It can be omitted, in which case a WWN will be
179 generated based on the MAC address of the specified MAC interface.
180 -p HBA_port_WWN, --port HBA_port_WWN
183 Retrieve remote port information from the HBA_port_WWN of the local
185 HBA port on the host. When used with the remote-port subcommand,
186 the -p option is mandatory.
187 When used with NPIV options, specify a virtual port WWN. If used
189 with create-npiv-port, it can be omitted, and a random based WWN
190 will be used. It is mandatory for delete-npiv-port.
191 When used with create-fcoe-port subcommand, specify the port WWN
193 for the FCoE port. It can be omitted, in which case a WWN will be
194 generated based on the MAC address of the specified MAC interface.
195 -s, --scsi-target
198 Lists the SCSI target information for all remote ports the user has
200 asked for. The -p, --port option must always be specified and must
201 be a valid HBA port on the host. This HBA port will be used as the
202 initiator for which to retrieve the SCSI level target information.
203 Note that this will only function on remote port fibre channel
204 World-Wide Names that support an FC4 type of SCSI. This option
205 applies only to an initiator mode port.
206 -t [HBA_node_WWN], -target [HBA_node_WWN]
209 Lists the information for the port with the target mode referenced
211 by the specified HBA_node_WWN or all target mode ports discovered
212 in the host.
213 When used with create-fcoe-port, create a FCoE target mode port.
215 -v, --verbose
218 When used with the logical-unit subcommand, the -v displays addi‐
220 tional information for the logical unit, including SCSI vendor and
221 product information and device type as well as the FC World-Wide
222 names for the local and remote fibre channel ports to which this
223 device is attached.
224 -V, --version
227 Displays the version information.
229 -?, --help
232 Displays the usage information.
234
237 Example 1 Listing All HBA Ports
238 The following command lists all initiator mode fibre channel HBA ports
241 on the host:
242 # fcinfo hba-port
245 HBA Port WWN: 210000e08b074cb5
247 Port Mode: Initiator
248 OS Device Name: /dev/cfg/c1
249 Manufacturer: QLogic Corp.
250 Model: 375-3108-xx
251 Firmware Version: 3.3.116
252 FCode/BIOS Version: 1.13.08
253 Serial Number: not available
254 Driver Name: qlc
255 Driver Version: 20070212-2.19
256 Type: N-port
257 State: online
258 Supported Speeds: 1Gb 2Gb
259 Current Speed: 2Gb
260 Node WWN: 200000e08b074cb5
261 NPIV Port List:
262 Virtual Port 1:
263 Port WWN: 200000e08b074cb1
264 Node WWN: 200000e08b074cb3
265 HBA Port WWN: 210100e08b274cb5
266 Port Mode: Initiator
267 OS Device Name: /dev/cfg/c2
268 Manufacturer: QLogic Corp.
269 Model: 375-3108-xx
270 Firmware Version: 3.3.116
271 FCode/BIOS Version: 1.13.08
272 Serial Number: not available
273 Driver Name: qlc
274 Driver Version: 20070212-2.19
275 Type: N-port
276 State: online
277 Supported Speeds: 1Gb 2Gb
278 Current Speed: 2Gb
279 Node WWN: 200100e08b274cb5
280 HBA Port WWN: 210000e08b072ab5
281 Port Mode: Initiator
282 OS Device Name: /dev/cfg/c3
283 Manufacturer: QLogic Corp.
284 Firmware Version: 3.3.116
285 FCode/BIOS Version: 1.13.08
286 Model: 375-3108-xx
287 Serial Number: not available
288 Driver Name: qlc
289 Driver Version: 20070212-2.19
290 Type: L-port
291 State: online
292 Supported Speeds: 1Gb 2Gb
293 Current Speed: 2Gb
294 Node WWN: 200000e08b072ab5
295 HBA Port WWN: 210100e08b272ab5
296 Port Mode: Initiator
297 OS Device Name: /dev/cfg/c4
298 Manufacturer: QLogic Corp.
299 Model: 375-3108-xx
300 Firmware Version: 3.3.116
301 FCode/BIOS Version: 1.13.08
302 Serial Number: 0402F00-0549112808
303 Driver Name: qlc
304 Driver Version: 20070212-2.19
305 Type: N-port
306 State: online
307 Supported Speeds: 1Gb 2Gb
308 Current Speed: 2Gb
309 Node WWN: 200100e08b272ab5
310 Example 2 Listing Target Mode HBA Ports
314 The following command lists all target mode fibre channel HBA ports on
317 the host:
318 # fcinfo hba-port -t
321 HBA Port WWN: 210100e08bb09221
322 Port Mode: Target
323 Port ID: 10700
324 OS Device Name: Not Applicable
325 Manufacturer: QLogic Corp.
326 Model: d30ac7e0
327 Firmware Version: 4.0.109
328 FCode/BIOS Version: N/A
329 Type: F-port
330 State: online
331 Supported Speeds: not established
332 Current Speed: 2Gb
333 Node WWN: 200100e08bb09221
334 HBA Port WWN: 210000e08b909221
335 Port Mode: Target
336 Port ID: 10900
337 OS Device Name: Not Applicable
338 Manufacturer: QLogic Corp.
339 Model: d37ad1e0
340 Firmware Version: 4.0.109
341 FCode/BIOS Version: N/A
342 Type: F-port
343 State: online
344 Supported Speeds: not established
345 Current Speed: 2Gb
346 Node WWN: 200000e08b909221
347 HBA Port WWN: 200000144fc2d508
348 Port Mode: Target
349 Port ID: 9a0025
350 OS Device Name: Not Applicable
351 Manufacturer: Sun Microsystems, Inc.
352 Model: FCoE Virtual FC HBA
353 Firmware Version: N/A
354 FCode/BIOS Version: N/A
355 Serial Number: N/A
356 Driver Name: COMSTAR FCOET
357 Driver Version: 1.0
358 Type: F-port
359 State: online
360 Supported Speeds: 1Gb 10Gb
361 Current Speed: 10Gb
362 Node WWN: 100000144fc2d508
363 HBA Port WWN: 200000144fc2d509
364 Port Mode: Target
365 Port ID: 9a0023
366 OS Device Name: Not Applicable
367 Manufacturer: Sun Microsystems, Inc.
368 Model: FCoE Virtual FC HBA
369 Firmware Version: N/A
370 FCode/BIOS Version: N/A
371 Serial Number: N/A
372 Driver Name: COMSTAR FCOET
373 Driver Version: 1.0
374 Type: F-port
375 State: online
376 Supported Speeds: 1Gb 10Gb
377 Current Speed: 10Gb
378 Node WWN: 100000144fc2d509
379 Example 3 Listing HBA Ports and Link Statistics
383 The following command lists information for the HBA ports and the link
386 statistics for those ports:
387 # fcinfo hba-port -l 210000e08b074cb5 210100e08b274cb5
390 HBA Port WWN: 210000e08b074cb5
392 Port Mode: Initiator
393 OS Device Name: /dev/cfg/c1
394 Manufacturer: QLogic Corp.
395 Model: 375-3108-xx
396 Firmware Version: 3.3.116
397 FCode/BIOS Version: 1.13.08
398 Serial Number: 0402F00-0549112808
399 Driver Name: qlc
400 Driver Version: 20070212-2.19
401 Type: N-port
402 State: online
403 Supported Speeds: 1Gb 2Gb
404 Current Speed: 2Gb
405 Node WWN: 200000e08b074cb5
406 Link Error Statistics:
407 Link Failure Count: 0
408 Loss of Sync Count: 0
409 Loss of Signal Count: 0
410 Primitive Seq Protocol Error Count: 0
411 Invalid Tx Word Count: 0
412 Invalid CRC Count: 0
413 HBA Port WWN: 210100e08b274cb5
414 Port Mode: Initiator
415 OS Device Name: /dev/cfg/c2
416 Manufacturer: QLogic Corp.
417 Model: 375-3108-xx
418 Firmware Version: 3.3.116
419 FCode/BIOS Version: 1.13.08
420 Serial Number: 0402F00-0549112808
421 Driver Name: qlc
422 Driver Version: 20070212-2.19
423 Type: N-port
424 State: online
425 Supported Speeds: 1Gb 2Gb
426 Current Speed: 2Gb
427 Node WWN: 200100e08b274cb5
428 Link Error Statistics:
429 Link Failure Count: 0
430 Loss of Sync Count: 0
431 Loss of Signal Count: 0
432 Primitive Seq Protocol Error Count: 0
433 Invalid Tx Word Count: 0
434 Invalid CRC Count: 0
435 Example 4 Listing All Remote Ports
439 The following command lists all remote ports that are visible through
442 the given HBA port:
443 # fcinfo remote-port -p 210100e08b274cb5
446 Remote Port WWN: 50020f230000b4af
448 Active FC4 Types: SCSI
449 SCSI Target: yes
450 Port Symbolic Name: unknown
451 Node WWN: 50020f200000b4af
452 Remote Port WWN: 210000e08b07daa6
453 Active FC4 Types: SCSI
454 SCSI Target: no
455 Port Symbolic Name: unknown
456 Node WWN: 200000e08b07daa6
457 Remote Port WWN: 20030003ba27c788
458 Active FC4 Types: SCSI
459 SCSI Target: yes
460 Port Symbolic Name: unknown
461 Node WWN: 10000003ba27c788
462 Remote Port WWN: 210000e08b096a60
463 Active FC4 Types: SCSI,IP
464 SCSI Target: no
465 Port Symbolic Name: unknown
466 Node WWN: 200000e08b096a60
467 Example 5 Listing Remote Ports and Link Statistics
471 The following command lists information for the remote ports and the
474 link statistics for those ports:
475 # fcinfo remote-port -l -p 210100e08b272ab5
478 Remote Port WWN: 210100e08b296a60
480 Active FC4 Types: SCSI,IP
481 SCSI Target: no
482 Port Symbolic Name: unknown
483 Node WWN: 200100e08b296a60
484 Link Error Statistics:
485 Link Failure Count: 0
486 Loss of Sync Count: 0
487 Loss of Signal Count: 0
488 Primitive Seq Protocol Error Count: 0
489 Invalid Tx Word Count: 0
490 Invalid CRC Count: 0
491 Remote Port WWN: 20030003ba27d56d
492 Active FC4 Types: SCSI
493 SCSI Target: yes
494 Port Symbolic Name: unknown
495 Node WWN: 10000003ba27d56d
496 Link Error Statistics:
497 Link Failure Count: 0
498 Loss of Sync Count: 4765165
499 Loss of Signal Count: 4765165
500 Primitive Seq Protocol Error Count: 0
501 Invalid Tx Word Count: 0
502 Invalid CRC Count: 0
503 Remote Port WWN: 210100e08b27f7a6
504 Active FC4 Types: SCSI
505 SCSI Target: no
506 Port Symbolic Name: unknown
507 Node WWN: 200100e08b27f7a6
508 Link Error Statistics:
509 Link Failure Count: 0
510 Loss of Sync Count: 0
511 Loss of Signal Count: 0
512 Primitive Seq Protocol Error Count: 0
513 Invalid Tx Word Count: 0
514 Invalid CRC Count: 0
515 Remote Port WWN: 50020f230000b897
516 Active FC4 Types: SCSI
517 SCSI Target: yes
518 Port Symbolic Name: unknown
519 Node WWN: 50020f200000b897
520 Link Error Statistics:
521 Link Failure Count: 0
522 Loss of Sync Count: 7
523 Loss of Signal Count: 7
524 Primitive Seq Protocol Error Count: 0
525 Invalid Tx Word Count: 0
526 Invalid CRC Count: 0
527 Remote Port WWN: 210100e08b27daa6
528 Active FC4 Types: SCSI
529 SCSI Target: no
530 Port Symbolic Name: unknown
531 Node WWN: 200100e08b27daa6
532 Link Error Statistics:
533 Link Failure Count: 0
534 Loss of Sync Count: 0
535 Loss of Signal Count: 0
536 Primitive Seq Protocol Error Count: 0
537 Invalid Tx Word Count: 0
538 Invalid CRC Count: 0
539 Remote Port WWN: 210000e08b074cb5
540 Active FC4 Types: SCSI,IP
541 SCSI Target: no
542 Port Symbolic Name: unknown
543 Node WWN: 200000e08b074cb5
544 Link Error Statistics:
545 Link Failure Count: 0
546 Loss of Sync Count: 0
547 Loss of Signal Count: 0
548 Primitive Seq Protocol Error Count: 0
549 Invalid Tx Word Count: 0
550 Invalid CRC Count: 0
551 Remote Port WWN: 210100e08b296060
552 Active FC4 Types: SCSI
553 SCSI Target: no
554 Port Symbolic Name: unknown
555 Node WWN: 200100e08b296060
556 Link Error Statistics:
557 Link Failure Count: 0
558 Loss of Sync Count: 0
559 Loss of Signal Count: 0
560 Primitive Seq Protocol Error Count: 0
561 Invalid Tx Word Count: 0
562 Invalid CRC Count: 0
563 Example 6 Listing All SCSI Targets and Link Statistics
567 The following command lists all remote ports as well as the link sta‐
570 tistics and scsi-target information:
571 # fcinfo remote-port -sl -p 210100e08b272ab5
574 Remote Port WWN: 210100e08b296a60
576 Active FC4 Types: SCSI,IP
577 SCSI Target: no
578 Port Symbolic Name: unknown
579 Node WWN: 200100e08b296a60
580 Link Error Statistics:
581 Link Failure Count: 0
582 Loss of Sync Count: 0
583 Loss of Signal Count: 0
584 Primitive Seq Protocol Error Count: 0
585 Invalid Tx Word Count: 0
586 Invalid CRC Count: 0
587 Remote Port WWN: 20030003ba27d56d
588 Active FC4 Types: SCSI
589 SCSI Target: yes
590 Port Symbolic Name: unknown
591 Node WWN: 10000003ba27d56d
592 Link Error Statistics:
593 Link Failure Count: 0
594 Loss of Sync Count: 4765165
595 Loss of Signal Count: 4765165
596 Primitive Seq Protocol Error Count: 0
597 Invalid Tx Word Count: 0
598 Invalid CRC Count: 0
599 LUN: 0
600 Vendor: SUN
601 Product: T4
602 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2
603 LUN: 1
604 Vendor: SUN
605 Product: T4
606 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2
607 Remote Port WWN: 210100e08b27f7a6
608 Active FC4 Types: SCSI
609 SCSI Target: no
610 Port Symbolic Name: unknown
611 Node WWN: 200100e08b27f7a6
612 Link Error Statistics:
613 Link Failure Count: 0
614 Loss of Sync Count: 0
615 Loss of Signal Count: 0
616 Primitive Seq Protocol Error Count: 0
617 Invalid Tx Word Count: 0
618 Invalid CRC Count: 0
619 Remote Port WWN: 50020f230000b897
620 Active FC4 Types: SCSI
621 SCSI Target: yes
622 Port Symbolic Name: unknown
623 Node WWN: 50020f200000b897
624 Link Error Statistics:
625 Link Failure Count: 0
626 Loss of Sync Count: 7
627 Loss of Signal Count: 7
628 Primitive Seq Protocol Error Count: 0
629 Invalid Tx Word Count: 0
630 Invalid CRC Count: 0
631 LUN: 0
632 Vendor: SUN
633 Product: T300
634 OS Device Name: Unknown
635 LUN: 1
636 Vendor: SUN
637 Product: T300
638 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2
639 LUN: 2
640 Vendor: SUN
641 Product: T300
642 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2
643 LUN: 3
644 Vendor: SUN
645 Product: T300
646 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2
647 LUN: 4
648 Vendor: SUN
649 Product: T300
650 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2
651 LUN: 5
652 Vendor: SUN
653 Product: T300
654 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2
655 LUN: 6
656 Vendor: SUN
657 Product: T300
658 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2
659 LUN: 7
660 Vendor: SUN
661 Product: T300
662 OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2
663 LUN: 8
664 Vendor: SUN
665 Product: T300
666 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2
667 LUN: 9
668 Vendor: SUN
669 Product: T300
670 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2
671 LUN: 10
672 Vendor: SUN
673 Product: T300
674 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2
675 LUN: 11
676 Vendor: SUN
677 Product: T300
678 OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2
679 LUN: 12
680 Vendor: SUN
681 Product: T300
682 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2
683 LUN: 13
684 Vendor: SUN
685 Product: T300
686 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2
687 LUN: 14
688 Vendor: SUN
689 Product: T300
690 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2
691 LUN: 15
692 Vendor: SUN
693 Product: T300
694 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2
695 Remote Port WWN: 210100e08b27daa6
696 Active FC4 Types: SCSI
697 SCSI Target: no
698 Port Symbolic Name: unknown
699 Node WWN: 200100e08b27daa6
700 Link Error Statistics:
701 Link Failure Count: 0
702 Loss of Sync Count: 0
703 Loss of Signal Count: 0
704 Primitive Seq Protocol Error Count: 0
705 Invalid Tx Word Count: 0
706 Invalid CRC Count: 0
707 Remote Port WWN: 210000e08b074cb5
708 Active FC4 Types: SCSI,IP
709 SCSI Target: no
710 Port Symbolic Name: unknown
711 Node WWN: 200000e08b074cb5
712 Link Error Statistics:
713 Link Failure Count: 0
714 Loss of Sync Count: 0
715 Loss of Signal Count: 0
716 Primitive Seq Protocol Error Count: 0
717 Invalid Tx Word Count: 0
718 Invalid CRC Count: 0
719 Remote Port WWN: 210100e08b296060
720 Active FC4 Types: SCSI
721 SCSI Target: no
722 Port Symbolic Name: unknown
723 Node WWN: 200100e08b296060
724 Link Error Statistics:
725 Link Failure Count: 0
726 Loss of Sync Count: 0
727 Loss of Signal Count: 0
728 Primitive Seq Protocol Error Count: 0
729 Invalid Tx Word Count: 0
730 Invalid CRC Count: 0
731 Example 7 Listing SCSI Target Information
735 The following command lists all remote ports as well as the scsi-target
738 information:
739 # fcinfo remote-port -s -p 210100e08b272ab5
742 Remote Port WWN: 210100e08b296a60
744 Active FC4 Types: SCSI,IP
745 SCSI Target: no
746 Port Symbolic Name: unknown
747 Node WWN: 200100e08b296060
748 Remote Port WWN: 20030003ba27d56d
749 Active FC4 Types: SCSI
750 SCSI Target: yes
751 Port Symbolic Name: unknown
752 Node WWN: 10000003ba27d56d
753 LUN: 0
754 Vendor: SUN
755 Product: T4
756 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2
757 LUN: 1
758 Vendor: SUN
759 Product: T4
760 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2
761 Remote Port WWN: 210100e08b27f7a6
762 Active FC4 Types: SCSI
763 SCSI Target: no
764 Port Symbolic Name: unknown
765 Node WWN: 200100e08b27f7a6
766 Remote Port WWN: 50020f230000b897
767 Active FC4 Types: SCSI
768 SCSI Target: yes
769 Port Symbolic Name: unknown
770 Node WWN: 50020f200000b897
771 LUN: 0
772 Vendor: SUN
773 Product: T300
774 OS Device Name: Unknown
775 LUN: 1
776 Vendor: SUN
777 Product: T300
778 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2
779 LUN: 2
780 Vendor: SUN
781 Product: T300
782 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2
783 LUN: 3
784 Vendor: SUN
785 Product: T300
786 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2
787 LUN: 4
788 Vendor: SUN
789 Product: T300
790 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2
791 LUN: 5
792 Vendor: SUN
793 Product: T300
794 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2
795 LUN: 6
796 Vendor: SUN
797 Product: T300
798 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2
799 LUN: 7
800 Vendor: SUN
801 Product: T300
802 OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2
803 LUN: 8
804 Vendor: SUN
805 Product: T300
806 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2
807 LUN: 9
808 Vendor: SUN
809 Product: T300
810 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2
811 LUN: 10
812 Vendor: SUN
813 Product: T300
814 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2
815 LUN: 11
816 Vendor: SUN
817 Product: T300
818 OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2
819 LUN: 12
820 Vendor: SUN
821 Product: T300
822 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2
823 LUN: 13
824 Vendor: SUN
825 Product: T300
826 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2
827 LUN: 14
828 Vendor: SUN
829 Product: T300
830 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2
831 LUN: 15
832 Vendor: SUN
833 Product: T300
834 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2
835 Remote Port WWN: 210100e08b27daa6
836 Active FC4 Types: SCSI
837 SCSI Target: no
838 Port Symbolic Name: unknown
839 Node WWN: 200100e08b27daa6
840 Remote Port WWN: 210000e08b074cb5
841 Active FC4 Types: SCSI,IP
842 SCSI Target: no
843 Port Symbolic Name: unknown
844 Node WWN: 200000e08b074cb5
845 Remote Port WWN: 210100e08b296060
846 Active FC4 Types: SCSI
847 SCSI Target: no
848 Port Symbolic Name: unknown
849 Node WWN: 200100e08b296060
850 Example 8 Listing the Logical Unit
854 The following command lists the logical unit:
857 # fcinfo logical-unit
860 /dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2
862 /dev/rdsk/c0t600C0FF00000000000362272539E5B03d0s2
863 /dev/rmt/0n
864 Example 9 Displaying Additional Information for the Logical Unit
868 The following command displays additional information about the logical
871 unit using the -v option for device /dev/rmt/On:
872 # fcinfo lu -v /dev/rmt/On
875 OS Device Name: /dev/rmt/0n
877 HBA Port WWN: 210000e07c030b91
878 Remote Port WWN: 21010003b7830a6
879 LUN: 0
880 Vendor: STK
881 Product: 9940A
882 Device Type: Tape device
883 The following command displays additional information about the logical
888 unit using the -v option for device
889 /dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2
890 # fcinfo logical-unit -v \
893 /dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2
894 OS Device Name: /dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2
896 HBA Port WWN: 210100e08b27a8a1
897 Remote Port WWN: 256000c0ffc03622
898 LUN: 0
899 Remote Port WWN: 216000c0ff803622
900 LUN: 0
901 HBA Port WWN: 210000e08b07a8a1
902 Remote Port WWN: 256000c0ffc03622
903 LUN: 0
904 Remote Port WWN: 216000c0ff803622
905 LUN: 0
906 Vendor: SUN
907 Product: StorEdge 3510
908 Device Type: Disk device
909 Example 10 Adding an NIPV Port
913 The following command adds an NPIV port to the HBA with a port name:
916 210000e08b170f1c
919 The NPIV port has a port name of 2000000000000001 and a node name of
924 2100000000000001.
925 # fcadm create-npiv-port -p 2000000000000001 -n 2100000000000001 \
928 210000e08b170f1c
929 Created NPIV Port:
931 HBA Port WWN: 2000000000000001
932 Node WWN: 2100000000000001
933 Physical HBA Port WWN: 210000e08b170f1c
934 Example 11 Adding an NIPV Port with Random WWN
938 The following command adds an NPIV port to the HBA with a randomly
941 assigned port name of 210000e08b170f1c.
942 # fcadm create-npiv-port 210000e08b170f1c
945 Created NPIV Port:
947 HBA Port WWN: 2038295824942801
948 Node WWN: 2100392849248001
949 Physical HBA Port WWN: 210000e08b170f1c
950 Example 12 Deleting an NIPV Port
954 The following command deletes an NPIV port.
957 # fcadm delete-npiv-port -p 2000000000000001 -w 2100000000000001 \
960 210000e08b170f1c
961 Example 13 Creating an FCoE Target Port
965 The following command creates an FCoE port associated with the MAC
968 interface nxge0.
969 # fcadm create-fcoe-port -t nxge0
972 Example 14 Deleting an FCoE Port
976 The following command deletes the FCoE port associated with the MAC
979 interface nxge0.
980 # fcadm delete-fcoe-port -t nxge0
983 Example 15 Listing Information for an FCoE Port
987 The following command lists information for FCoE ports.
990 # fcadm list-fcoe-ports
993 HBA Port WWN: 200000144fc2d508
994 Port Type: Target
995 MAC Name: nxge0
996 MTU Size: 9194
997 MAC Factory Address: 00144fc2d508
998 MAC Current Address: 00144fc2d508
999 HBA Port WWN: 200000144fc2d509
1000 Port Type: Target
1001 MAC Name: nxge1
1002 MTU Size: 9194
1003 MAC Factory Address: 00144fc2d509
1004 MAC Current Address: 00144fc2d509
1005 Example 16 Reinitializing the Link of an FC Port
1009 The following command forces the link connected with the port
1012 200000144fc2d508 to reinitialize.
1013 # fcadm force-lip 200000144fc2d508
1016
1020 See attributes(5) for descriptions of the following attributes:
1021 ┌─────────────────────────────┬─────────────────────────────┐
1026 │ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
1027 ├─────────────────────────────┼─────────────────────────────┤
1028 │Availability │SUNWfcprt │
1029 ├─────────────────────────────┼─────────────────────────────┤
1030 │Interface Stability │Committed │
1031 └─────────────────────────────┴─────────────────────────────┘
1032
1034 attributes(5)
1035
1037 Errors that can occur in addition to the errors normally associated
1038 with system administration commands:
1039 o HBA_port_WWN: not found
1041 o Remote_port_WWN: not found
1043 o HBA_port_WWN: NPIV not supported on this HBA
1045SunOS 5.11 26 Jul 2009 fcinfo(1M)