1ledmon(8) Intel(R) Enclosure LED Monitor Service ledmon(8)
2
3
4
6 ledmon - Intel(R) LED monitor service for storage enclosures.
7
9 ledmon [OPTIONS]
10
12 The ledmon application is a daemon process used to monitor a state of
13 software RAID devices (md only) or a state of block devices. The state
14 is visualizing on LEDs associated to each slot in an enclosure or a
15 drive bay. There are two types of system: 2-LEDs system (Activity LED,
16 Status LED) and 3-LEDs system (Activity LED, Locate LED, Fail LED).
17 This application has the highest priority when accessing the LEDs.
18
19 The ledmon application uses SGPIO and SES-2 protocol to control LEDs.
20 The program implements IBPI patterns of SFF-8489 specification for
21 SGPIO. Please note some enclosures do not stick close to SFF-8489
22 specification. It might happen that enclosure processor will accept
23 IBPI pattern but it will blink LEDs not according to SFF-8489
24 specification or it has limited number of patterns supported.
25
26 LED management (AHCI) and SAF-TE protocols are not supported.
27
28 There's no method provided to specify which RAID volume should be
29 monitored and which not. The ledmon application monitors all RAID
30 devices and visualizes their state.
31
32 The ledmon application has been verified to work with Intel(R) storage
33 controllers (i.e. Intel(R) AHCI controller and Intel(R) SAS
34 controller). The application might work with storage controllers of
35 other vendors (especially SAS/SCSI controllers). However storage
36 controllers of other vendors have not been tested.
37
38 The ledmon application is part of Intel(R) Enclosure LED Utilities.
39 Only single instance of the application is allowed.
40
42 -c or --config=path
43 Sets a path to local configuration file. If this option is
44 specified the global configuration file and user configuration
45 file has no effect.
46
47 -l or --log=path
48 Sets a path to local log file. If this option is specified the
49 global log file /var/log/ledmon.log is not used.
50
51 -t or --interval=seconds
52 Sets time interval between scans of sysfs. The value is given
53 in seconds. The minimum is 5 seconds the maximum is not
54 specified.
55
56 --quiet or --error or --warning or --info or --debug or --all
57 Verbose level - 'quiet' means no logging at all and 'all' means
58 to log everything. The levels are given in order. If user
59 specifies more then one verbose option the last option comes
60 into effect.
61
62 -h or --help
63 Prints this text out and exits.
64
65 -v or --version
66 Displays version of ledmon and information about the license
67 and exits.
68
70 /var/log/ledmon.log
71 Global log file, used by ledmon application. To force logging
72 to user defined file use -l option switch.
73
74 ~/.ledctl
75 User configuration file, shared between ledmon and all ledctl
76 application instances.
77
78 /etc/ledcfg.conf
79 Global configuration file, shared between ledmon and all ledctl
80 application instances.
81
83 Copyright (c) 2009-2013 Intel Corporation.
84
85 This program is distributed under the terms of the GNU General Public
86 License as published by the Free Software Foundation. See the build-in
87 help for details on the License and the lack of warranty.
88
90 The ledmon application does not recognize PFA state (Predicted Failure
91 Analysis), hence the PFA pattern from SFF-8489 specification is not
92 visualized.
93
95 ledctl(8), ledctl.conf(5)
96
98 This manual page was written by Artur Wojcik <artur.wojcik@intel.com>.
99 It may be used by others.
100
101
102
103LEDMON Version 0.79 November 2013 ledmon(8)