1FUNZIP(1L) FUNZIP(1L)
2
6 funzip - filter for extracting from a ZIP archive in a pipe
7
9 funzip [-password] [input[.zip|.gz]]
10
12 [-password]
13 Optional password to be used if ZIP archive is encrypted.
14 Decryption may not be supported at some sites. See DESCRIPTION
15 for more details.
16 [input[.zip|.gz]]
18 Optional input archive file specification. See DESCRIPTION for
19 details.
20
22 funzip without a file argument acts as a filter; that is, it assumes
23 that a ZIP archive (or a gzip'd(1) file) is being piped into standard
24 input, and it extracts the first member from the archive to stdout.
25 When stdin comes from a tty device, funzip assumes that this cannot be
26 a stream of (binary) compressed data and shows a short help text,
27 instead. If there is a file argument, then input is read from the
28 specified file instead of from stdin.
29 A password for encrypted zip files can be specified on the command line
31 (preceding the file name, if any) by prefixing the password with a
32 dash. Note that this constitutes a security risk on many systems; cur‐
33 rently running processes are often visible via simple commands (e.g.,
34 ps(1) under Unix), and command-line histories can be read. If the
35 first entry of the zip file is encrypted and no password is specified
36 on the command line, then the user is prompted for a password and the
37 password is not echoed on the console.
38 Given the limitation on single-member extraction, funzip is most useful
40 in conjunction with a secondary archiver program such as tar(1). The
41 following section includes an example illustrating this usage in the
42 case of disk backups to tape.
43
45 To use funzip to extract the first member file of the archive test.zip
46 and to pipe it into more(1):
47 funzip test.zip | more
49 To use funzip to test the first member file of test.zip (any errors
51 will be reported on standard error):
52 funzip test.zip > /dev/null
54 To use zip and funzip in place of compress(1) and zcat(1) (or gzip(1L)
56 and gzcat(1L)) for tape backups:
57 tar cf - . | zip -7 | dd of=/dev/nrst0 obs=8k
59 dd if=/dev/nrst0 ibs=8k | funzip | tar xf -
60 (where, for example, nrst0 is a SCSI tape drive).
62
64 When piping an encrypted file into more and allowing funzip to prompt
65 for password, the terminal may sometimes be reset to a non-echo mode.
66 This is apparently due to a race condition between the two programs;
67 funzip changes the terminal mode to non-echo before more reads its
68 state, and more then ``restores'' the terminal to this mode before
69 exiting. To recover, run funzip on the same file but redirect to
70 /dev/null rather than piping into more; after prompting again for the
71 password, funzip will reset the terminal properly.
72 There is presently no way to extract any member but the first from a
74 ZIP archive. This would be useful in the case where a ZIP archive is
75 included within another archive. In the case where the first member is
76 a directory, funzip simply creates the directory and exits.
77 The functionality of funzip should be incorporated into unzip itself
79 (future release).
80
82 gzip(1L), unzip(1L), unzipsfx(1L), zip(1L), zipcloak(1L), zipinfo(1L),
83 zipnote(1L), zipsplit(1L)
84
86 The Info-ZIP home page is currently at
87 http://www.info-zip.org/pub/infozip/
88 or
89 ftp://ftp.info-zip.org/pub/infozip/ .
90
92 Mark Adler (Info-ZIP)
93Info-ZIP 20 April 2009 (v3.95) FUNZIP(1L)