1EXIT(3) Linux Programmer's Manual EXIT(3)
2
6 exit - cause normal process termination
7
9 #include <stdlib.h>
10 void exit(int status);
12
14 The exit() function causes normal process termination and the value of
15 status & 0377 is returned to the parent (see wait(2)).
16 All functions registered with atexit(3) and on_exit(3) are called, in
18 the reverse order of their registration. (It is possible for one of
19 these functions to use atexit(3) or on_exit(3) to register an addi‐
20 tional function to be executed during exit processing; the new regis‐
21 tration is added to the front of the list of functions that remain to
22 be called.) If one of these functions does not return (e.g., it calls
23 _exit(2), or kills itself with a signal), then none of the remaining
24 functions is called, and further exit processing (in particular, flush‐
25 ing of stdio(3) streams) is abandoned. If a function has been regis‐
26 tered multiple times using atexit(3) or on_exit(3), then it is called
27 as many times as it was registered.
28 All open stdio(3) streams are flushed and closed. Files created by
30 tmpfile(3) are removed.
31 The C standard specifies two constants, EXIT_SUCCESS and EXIT_FAILURE,
33 that may be passed to exit() to indicate successful or unsuccessful
34 termination, respectively.
35
37 The exit() function does not return.
38
40 For an explanation of the terms used in this section, see
41 attributes(7).
42 ┌──────────┬───────────────┬─────────────────────┐
44 │Interface │ Attribute │ Value │
45 ├──────────┼───────────────┼─────────────────────┤
46 │exit() │ Thread safety │ MT-Unsafe race:exit │
47 └──────────┴───────────────┴─────────────────────┘
48 The exit() function uses a global variable that is not protected, so it
49 is not thread-safe.
50
52 POSIX.1-2001, POSIX.1-2008, C89, C99, SVr4, 4.3BSD.
53
55 The behavior is undefined if one of the functions registered using
56 atexit(3) and on_exit(3) calls either exit() or longjmp(3). Note that
57 a call to execve(2) removes registrations created using atexit(3) and
58 on_exit(3).
59 The use of EXIT_SUCCESS and EXIT_FAILURE is slightly more portable (to
61 non-UNIX environments) than the use of 0 and some nonzero value like 1
62 or -1. In particular, VMS uses a different convention.
63 BSD has attempted to standardize exit codes; see the file <sysexits.h>.
65 After exit(), the exit status must be transmitted to the parent
67 process. There are three cases:
68 · If the parent has set SA_NOCLDWAIT, or has set the SIGCHLD handler
70 to SIG_IGN, the status is discarded and the child dies immediately.
71 · If the parent was waiting on the child, it is notified of the exit
73 status and the child dies immediately.
74 · Otherwise, the child becomes a "zombie" process: most of the process
76 resources are recycled, but a slot containing minimal information
77 about the child process (termination status, resource usage statis‐
78 tics) is retained in process table. This allows the parent to sub‐
79 sequently use waitpid(2) (or similar) to learn the termination sta‐
80 tus of the child; at that point the zombie process slot is released.
81 If the implementation supports the SIGCHLD signal, this signal is sent
83 to the parent. If the parent has set SA_NOCLDWAIT, it is undefined
84 whether a SIGCHLD signal is sent.
85 Signals sent to other processes
87 If the exiting process is a session leader and its controlling terminal
88 is the controlling terminal of the session, then each process in the
89 foreground process group of this controlling terminal is sent a SIGHUP
90 signal, and the terminal is disassociated from this session, allowing
91 it to be acquired by a new controlling process.
92 If the exit of the process causes a process group to become orphaned,
94 and if any member of the newly orphaned process group is stopped, then
95 a SIGHUP signal followed by a SIGCONT signal will be sent to each
96 process in this process group. See setpgid(2) for an explanation of
97 orphaned process groups.
98 Except in the above cases, where the signalled processes may be chil‐
100 dren of the terminating process, termination of a process does not in
101 general cause a signal to be sent to children of that process. How‐
102 ever, a process can use the prctl(2) PR_SET_PDEATHSIG operation to
103 arrange that it receives a signal if its parent terminates.
104
106 _exit(2), get_robust_list(2), setpgid(2), wait(2), atexit(3),
107 on_exit(3), tmpfile(3)
108
110 This page is part of release 4.15 of the Linux man-pages project. A
111 description of the project, information about reporting bugs, and the
112 latest version of this page, can be found at
113 https://www.kernel.org/doc/man-pages/.
114Linux 2017-09-15 EXIT(3)