1OSPF6D(8) FRR OSPF6D(8)
2
6 ospf6d - an OSPFv3 routing engine for use with FRRouting.
7
9 ospf6d [-h] [-v]
10 ospf6d [-d|-t|-dt] [-C] [-f config-file] [-i pid-file] [-z
12 zclient-path] [-u user] [-g group] [-A vty-addr] [-P vty-port] [-M mod‐
13 ule[:options]] [-N pathspace] [--vty_socket vty-path] [--moduledir mod‐
14 ule-path]
15
17 ospf6d is a routing component that works with the FRRouting routing
18 engine.
19
21 OPTIONS available for the ospf6d command:
22 HELP AND VERSION
24 -h, --help
25 Print a short description of the daemon's command line options.
26 -v, --version
28 Print version and build information for the daemon.
29 Both of these options inhibit normal operation and will immediately
31 exit.
32 PROCESS CONTROL
34 These options control background operation:
35 -d, --daemon
37 Launches the process in background/daemon mode, forking and
38 detaching from the terminal.
39 The parent process will delay its exit until the daemon/child
41 has finished its initialization and has entered its main loop.
42 This is important for zebra startup because the other daemons
43 will attempt to connect to zebra. A return from zebra -d guaran‐
44 tees its readiness to accept these connections.
45 -t, --terminal
47 Opens an interactive VTY session on the terminal, allowing for
48 both state and configuration operations. Note that the terminal
49 starts operating after startup has completed and the configura‐
50 tion file has been loaded.
51 The process will exit when end of file is detected on the termi‐
53 nal. It is possible to daemonize a process started with -t (but
54 without -d) by sending SIGQUIT to the process (normally mapped
55 to a ^keypress.)
56 The combination of --daemon and --terminal will delay the daemon from
58 going into background until the terminal session ends (by end of file.)
59 If the process receives SIGINT (e.g. a ^C keypress) in this mode, it
61 will exit instead of daemonizing.
62 It is safe to suspend (SIGTSTP / ^Z) the terminal session opened by the
64 previous two options; this will only stop the terminal but not the
65 protocol daemon itself (which runs in a separate second process.)
66 CONFIGURATION AND PATHS
68 The following options control configuration and file system locations
69 for frr processes:
70 -f, --config_file config-file
72 Specify a configuration file to be used instead of the default
73 /etc/frr/<daemon>.conf file.
74 Note that the daemon will attempt to write to this file if the
76 write file command is issued on its VTY interface or through
77 vtysh.
78 -C, --dryrun
80 Load the configuration file and check its validity, then exit.
81 -i, --pid_file pid-file
83 Output a pid file to a location other than the default
84 /var/run/frr/<daemon>.pid.
85 -z, --socket zclient-path
87 Override the path of the ZAPI socket used to communicate between
88 zebra and the various protocol daemons. The default is
89 /var/run/frr/zserv.api. The value of this option must be the
90 same across all daemons.
91 -N, --pathspace pathspace
93 Insert pathspace into all default paths, changing the defaults
94 to:
95 /etc/frr/pathspace/<daemon>.conf /var/run/frr/pathspace/<dae‐
97 mon>.pid /var/run/frr/pathspace/<daemon>.vty
98 /var/run/frr/pathspace/zserv.api
99 ´.´ and ´/´ characters will not be accepted in pathspace, but
101 the empty string will be accepted.
102 Note that this only changes the respective defaults, it has no
104 effect on the respective path if the -f, -i, -z or --vty_socket
105 options are used.
106 The purpose of this option is to easily group all file system
108 related bits together for running multiple fully-separate "logi‐
109 cal routers" on a system, particularly with Linux network names‐
110 paces. Groups of daemons running with distinct pathspace values
111 will be completely unaware of each other and not interact in any
112 way.
113 This option does not do any system setup (like network names‐
115 paces.) This must be done by the user, for example by running:
116 ip netns exec namespace <daemon> -N namespace
118 PROCESS CREDENTIALS
120 -u, --user user
121 (default: frr)
122 -g, --group group
124 (default: frr)
125 Change the user/group which the daemon will switch to.
127 -S, --skip_runas
129 Skip setting the process effective user and group.
130 Note that there is an additional group, frrvty, which controls group
132 ownership of the VTY sockets. The name of this group cannot currently
133 be changed, and user must be a member of this group.
134 VTY SETUP
136 These following options control the daemon's VTY (interactive command
137 line) interface. The interface is available over TCP, using the telnet
138 protocol, as well as through the vtysh frontend.
139 -A, --vty_addr vty-addr
141 Specify an IP/IPv6 address to bind the TCP VTY interface to. It
142 is generally recommended to specify ::1 or 127.0.0.1. For rea‐
143 sons of backwards compatibility, the default is to listen on all
144 interfaces.
145 -P, --vty_port vty-port
147 Override the daemon's default TCP VTY port (each daemon has a
148 different default value upwards of 2600, listed below.) Speci‐
149 fying 0 disables the TCP VTY interface.
150 Default ports are::
152 zebra 2601
154 ripd 2602
155 ripngd 2603
156 ospfd 2604
157 bgpd 2605
158 ospf6d 2606
159 isisd 2608
160 babeld 2609
161 nhrpd 2610
162 pimd 2611
163 ldpd 2612
164 eigrpd 2613
165 pbrd 2615
166 staticd 2616
167 bfdd 2617
168 fabricd 2618
169 Port 2607 is used for ospfd's Opaque LSA API.
171 --vty_socket vty-path
173 Overrides the directory used for the <daemon>.vty sockets.
174 vtysh connects to these sockets in order to access each daemon's
175 VTY. Default: /var/run/frr[/<pathspace>]
176 NB: Unlike the other options, this option specifies a directory,
178 not a full path.
179 This option is primarily used by the SNAP packaging system, its
181 semantics may change. It should not be necessary in most other
182 scenarios.
183 MODULE LOADING
185 frr supports optional dynamically loadable modules, although these can
186 only be loaded at startup. The set of available modules may vary
187 across distributions and packages, and modules may be available for
188 installation as separate packages.
189 -M, --module module[:options]
191 Load a module named module, optionally passing options to it.
192 If there is a ´/´ character in module, the value is assumed to
194 be a pathname to a module.
195 If there is no ´/´ character, the module directory (see next
197 option) is searched first for a module named "<daemon>_<mod‐
198 ule>.so", then for "<module>.so". This allows for a module to
199 exist in variations appropriate for particular daemons, e.g.
200 zebra_snmp and bgp_snmp, with the correct one selected by -M
201 snmp.
202 The meaning of options is specific to the module being loaded.
204 Most modules currently ignore it.
205 Modules are loaded in the order as listed on the command line.
207 This is not generally relevant.
208 --moduledir module-path
210 Look for modules in the module-path directory instead of the
211 default /usr/lib/frr/modules. (This path is not affected by the
212 -N option.)
213 The list of loaded modules can be inspected at runtime with the show
215 modules VTY command.
216
218 /usr/lib/frr/ospf6d
219 The default location of the ospf6d binary.
220 /etc/frr/ospf6d.conf
222 The default location of the ospf6d config file.
223 $(PWD)/ospf6d.log
225 If the ospf6d process is configured to output logs to a file,
226 then you will find this file in the directory where you started
227 ospf6d.
228
230 This man page is intended to be a quick reference for command line
231 options. The definitive document is the info file frr 7.1 or the docu‐
232 mentation available on the project website at https://frrouting.org/.
233
235 The daemon may log to standard output, to a VTY, to a log file, or
236 through syslog to the system logs. FRR supports many debugging options,
237 see the Info file, web docs or source for details.
238
240 zebra(8), vtysh(1), ripd(8), ripngd(8), ospfd(8), ospf6d(8), bgpd(8),
241 isisd(8), babeld(8), nhrpd(8), pimd(8), pbrd(8), ldpd(8), eigrpd(8),
242 staticd(8), fabricd(8), mtracebis(8) https://frrouting.org/
243
245 FRR eats bugs for breakfast. If you have food for the maintainers,
246 please email <dev@lists.frrouting.org>.
247
249 2019, FRR
2507.1 Oct 07, 2019 OSPF6D(8)