1Smokeping_probes_IOSPing(3)        SmokePing       Smokeping_probes_IOSPing(3)
2
3
4

NAME

6       Smokeping::probes::IOSPing - Cisco IOS Probe for SmokePing
7

SYNOPSIS

9        *** Probes ***
10
11        +IOSPing
12
13        binary = /usr/bin/rsh # mandatory
14        forks = 5
15        offset = 50%
16        packetsize = 56
17        step = 300
18        timeout = 15
19
20        # The following variables can be overridden in each target section
21        ioshost = my.cisco.router # mandatory
22        iosint = Ethernet 1/0
23        iosuser = admin
24        pings = 5
25
26        # [...]
27
28        *** Targets ***
29
30        probe = IOSPing # if this should be the default probe
31
32        # [...]
33
34        + mytarget
35        # probe = IOSPing # if the default probe is something else
36        host = my.host
37        ioshost = my.cisco.router # mandatory
38        iosint = Ethernet 1/0
39        iosuser = admin
40        pings = 5
41

DESCRIPTION

43       Integrates Cisco IOS as a probe into smokeping.  Uses the rsh / remsh
44       protocol to run a ping from an IOS device.
45

VARIABLES

47       Supported probe-specific variables:
48
49       binary
50           The binary option specifies the path of the binary to be used to
51           connect to the IOS device.  Commonly used binaries are /usr/bin/rsh
52           and /usr/bin/remsh, although any script or binary should work if
53           can be called as
54
55               /path/to/binary [ -l user ] router ping
56
57           to produce the IOS ping dialog on stdin & stdout.
58
59           Example value: /usr/bin/rsh
60
61           This setting is mandatory.
62
63       forks
64           Run this many concurrent processes at maximum
65
66           Example value: 5
67
68           Default value: 5
69
70       offset
71           If you run many probes concurrently you may want to prevent them
72           from hitting your network all at the same time. Using the probe-
73           specific offset parameter you can change the point in time when
74           each probe will be run. Offset is specified in % of total interval,
75           or alternatively as 'random', and the offset from the 'General'
76           section is used if nothing is specified here. Note that this does
77           NOT influence the rrds itself, it is just a matter of when data
78           acqusition is initiated.  (This variable is only applicable if the
79           variable 'concurrentprobes' is set in the 'General' section.)
80
81           Example value: 50%
82
83       packetsize
84           The (optional) packetsize option lets you configure the packetsize
85           for the pings sent.
86
87           Default value: 56
88
89       step
90           Duration of the base interval that this probe should use, if
91           different from the one specified in the 'Database' section. Note
92           that the step in the RRD files is fixed when they are originally
93           generated, and if you change the step parameter afterwards, you'll
94           have to delete the old RRD files or somehow convert them. (This
95           variable is only applicable if the variable 'concurrentprobes' is
96           set in the 'General' section.)
97
98           Example value: 300
99
100       timeout
101           How long a single 'ping' takes at maximum
102
103           Example value: 15
104
105           Default value: 5
106
107       Supported target-specific variables:
108
109       ioshost
110           The ioshost option specifies the IOS device which should be used
111           for the ping.
112
113           Example value: my.cisco.router
114
115           This setting is mandatory.
116
117       iosint
118           The (optional) iosint option allows you to specify the source
119           address or interface in the IOS device. The value should be an IP
120           address or an interface name such as "Ethernet 1/0". If this option
121           is omitted, the IOS device will pick the IP address of the outbound
122           interface to use.
123
124           Example value: Ethernet 1/0
125
126       iosuser
127           The (optional) iosuser option allows you to specify the remote
128           username the IOS device.  If this option is omitted, the username
129           defaults to the default user used by the remsh command (usually the
130           user running the remsh command, ie the user running SmokePing).
131
132           Example value: admin
133
134       pings
135           How many pings should be sent to each target, if different from the
136           global value specified in the Database section. Note that the
137           number of pings in the RRD files is fixed when they are originally
138           generated, and if you change this parameter afterwards, you'll have
139           to delete the old RRD files or somehow convert them.
140
141           Example value: 5
142

AUTHORS

144       Paul J Murphy <paul@murph.org>
145
146       based on Smokeping::probes::FPing by
147
148       Tobias Oetiker <tobi@oetiker.ch>
149

NOTES

151   IOS Configuration
152       The IOS device must have rsh enabled and an appropriate trust defined,
153       eg:
154
155           !
156           ip rcmd rsh-enable
157           ip rcmd remote-host smoke 192.168.1.2 smoke enable
158           !
159
160       Some IOS devices have a maximum of 5 VTYs available, so be careful not
161       to hit a limit with the 'forks' variable.
162
163   Password authentication
164       It is not possible to use password authentication with rsh or remsh due
165       to fundamental limitations of the protocol.
166
167   Ping packet size
168       The FPing manpage has the following to say on the topic of ping packet
169       size:
170
171       Number of bytes of ping data to send.  The minimum size (normally 12)
172       allows room for the data that fping needs to do its work (sequence
173       number, timestamp).  The reported received data size includes the IP
174       header (normally 20 bytes) and ICMP header (8 bytes), so the minimum
175       total size is 40 bytes.  Default is 56, as in ping. Maximum is the
176       theoretical maximum IP datagram size (64K), though most systems limit
177       this to a smaller, system-dependent number.
178
179
180
1812.7.3                             2021-03-11       Smokeping_probes_IOSPing(3)
Impressum